Fuel Pumps and Accessories
Fuel Pumps and Accessories

Fuel Pumps

Fuel Pumps and Accessories

Fuel Pumps and Accessories

!
WFP509
Airtex 6 Volt Low-Pressure Fuel Pump

Airtex 6 Volt Low-Pressure Fuel Pump

This is a special fuel pump for vehicles with a 6 Volt electrical system.

Thanks to its low output pressure of 4.4 PSI / 0.3 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

Pump specification:

  • Flow rate: 8 Gallons/hour - 30 liters/hour
  • Pressure: 4.4 PSI / 0.3 Bar
  • Pipe union thread size: 1/8" NPTF tapered thread
  • Power supply: 6 Volt Negative Earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • In-line fuel filter
  • Mounting bracket and materials
  • 8 mm inlet and outlet unions with fuel hose and hose clips
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Always operate this pump with the proper filter installed as failure to do so will void the warranty!
Replacement filters can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

Airtex 6 Volt Low-Pressure Fuel Pump

WFP502
Airtex 12 Volt Low-Pressure Fuel Pump

Airtex 12 Volt Low-Pressure Fuel Pump

This is a special, low-pressure fuel pump for vehicles with a 12 Volt electrical system.

Thanks to its low pressure of 4.5 PSI / 0.31 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

Pump specification:

  • Flow rate: 90 - 130 liters/hour
  • Pressure: 2.5 - 4.5 PSI / 0.17 - 0.31 Bar
  • Pipe union thread size: 1/8" NPTF tapered thread
  • Power supply: 12 Volt Negative Earth
  • Pump Length: 172 mm
  • Pump Diameter: 54 mm
  • Draws a current of some 5 Amps
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

The kit includes:

  • Pump
  • In-line fuel filter
  • Mounting bracket and materials
  • 8 mm inlet and outlet unions with fuel hose and hose clips
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Always operate this pump with the proper filter installed as failure to do so will void the warranty!
Replacement filters can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Airtex 12 Volt Low-Pressure Fuel Pump

SSRK
Facet CUBE Solid State ROAD Fuel Pump Kit

Facet CUBE Solid State ROAD Fuel Pump Kit

Facet Solid State ROAD Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State ROAD fuel pump is suitable for engines of up to circa 130 HP.

Pump specification:

  • Flow rate 12 Gallons/hour - 45 liters/hour
  • Pressure: 2.5 - 3.0 PSI - 0.17 - 0.20 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State ROAD Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State ROAD Fuel Pump Kit

SSR
Facet CUBE Solid State ROAD Fuel Pump - Pump Only

Facet CUBE Solid State ROAD Fuel Pump - Pump Only

Facet CUBE Solid State ROAD Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State ROAD fuel pump is suitable for engines of up to circa 130 HP.

Pump specification:

  • Flow rate 12 Gallons/hour - 45 liters/hour
  • Pressure: 2.5 - 3.0 PSI - 0.17 - 0.20 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State ROAD Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State ROAD Fuel Pump - Pump Only

SSFRK
Facet CUBE Solid State FAST ROAD Fuel Pump Kit

Facet CUBE Solid State FAST ROAD Fuel Pump Kit

Facet Solid State FAST ROAD Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State FAST ROAD fuel pump is suitable for engines of up to circa 150 HP.

Pump specification:

  • Flow rate 32 Gallons/hour - 120 liters / hour
  • Pressure: 4 - 7 PSI - 0.27 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State FAST ROAD Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State FAST ROAD Fuel Pump Kit

SSFR
Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

Facet CUBE Solid State FAST ROAD Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State FAST ROAD fuel pump is suitable for engines of up to circa 150 HP.

Pump specification:

  • Flow rate 32 Gallons/hour - 120 liters / hour
  • Pressure: 4 - 7 PSI - 0.27 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State FAST ROAD Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

SSCK
Facet CUBE Solid State COMPETITION Fuel Pump Kit

Facet CUBE Solid State COMPETITION Fuel Pump Kit

Facet Solid State COMPETITION Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State COMPETITION fuel pump is suitable for engines of up to circa 180 HP.

Pump specification:

  • Flow rate 25 Gallons/hour - 95 liters/hour
  • Pressure: 6.0 - 7.0 PSI - 0.41 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State COMPETITION Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State COMPETITION Fuel Pump Kit

SSC
Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

Facet CUBE Solid State COMPETITION Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State COMPETITION fuel pump is suitable for engines of up to circa 180 HP.

Pump specification:

  • Flow rate 25 Gallons/hour - 95 liters/hour
  • Pressure: 6.0 - 7.0 PSI - 0.41 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State COMPETITION Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

FPA906

1/8'' Screw-On Fuel Pump Filter

This is a special screw-on fuel filter to be used with a variety of electric fuel pumps.

Failure to operate those pumps with a suitable filter like this usually voids the warranty on the pump!

This filter suits, amongst others, the Airtex 6Volt filter and the range of Solid State fuel filters by Facet.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Union for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

1/8'' Screw-On Fuel Pump Filter

RTWK
Facet GOLD-FLO Red top Competition Fuel Pump Kit

Facet GOLD-FLO Red top Competition Fuel Pump Kit

Facet GOLD-FLO Red top competition fuel pump kit suitable for engines of 200+ BHP.

Pump specification:

  • Flow rate 45 Gallons/hour / 170 liters/hour
  • Pressure: 6.5 - 8 PSI / 0.45 - 0.55 Bar
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • Mounting isolation feet
  • 10 mm Inlet and outlet unions
  • Spare internal filter
  • Terminated earthing wire
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread
Fuel Unions for fuel lines with 10 mm internal diameter

Due to its operating pressure of up to 8 PSI (some 0.55 Bar), the GOLD-FLO Red Top Competition pump usually requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet GOLD-FLO Red top Competition Fuel Pump Kit

RTW
Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

Facet Red Top competition fuel pump, suitable for engines of 200+ BHP.

Pump specification:

  • Flow rate 45 Gallons/hour / 170 liters/hour
  • Pressure: 6.5 - 8 PSI / 0.45 - 0.55 Bar
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread

Due to its operating pressure of up to 8 PSI (some 0.55 Bar), the GOLD-FLO Red Top Competition pump usually requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

476088
Facet GOLD-FLO 24 Volt Fuel Pump - Pump only

Facet GOLD-FLO 24 Volt Fuel Pump - Pump only

Facet 24 Volt fuel pump.

Specifically designed for vehicles and applications with a 24 Volt electrical system.

Pump specification:

  • Flow rate 32 Gallons/hour / 120 liters/hour
  • Pressure: 4 - 5 PSI (0.28 - 0.35 Bar)
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 24 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread

It could be that your fuel system operates at a lower pressure than this pump delivers.
If this is the case, it requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

Facet GOLD-FLO 24 Volt Fuel Pump - Pump only

FPA905
Facet Fuel Pump Mounting Kit

Facet Fuel Pump Mounting Kit

Facet Fuel Pump Mounting Kit.

Antivibration mounts + earthing wire for Facet Cube, GOLD-FLO and Interrupter series fuel pumps.

Facet Fuel Pump Mounting Kit

HUCOPUMPFP02
Huco Low-Pressure 12 Volt Fuel Pump Kit - Suction Type

Huco Low-Pressure 12 Volt Fuel Pump Kit - Suction Type

Huco Low-Pressure 12 Volt Fuel Pump Kit.

Hüco fuel pump for engines of up to some 160 BHP.

This is a "suction type" pump, intended to placed in the engine compartment of your vehicle.

Please see HUCOPUMPFP03 in case you require a "pressure type" pump to be placed near the fuel tank of your vehicle.

Pump specification:

  • Flow rate 27.5 Gallons/hour / 125 liters/hour
  • Pressure: 2.1 PSI / 0.15 Bar
  • 12 - 14 Volt - negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol or Bio-Diesel

Kit includes:

  • Pump
  • Mounting bracket

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Thanks to its operating pressure of 2.1 PSI (some 0.15 Bar), this Huco pump does not require a pressure regulator which makes it a very cost-efficient proposition.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Huco Low-Pressure 12 Volt Fuel Pump Kit - Suction Type

HUCOPUMPFP03
Huco Low-Pressure 12 Volt Fuel Pump Kit - Pressure Type

Huco Low-Pressure 12 Volt Fuel Pump Kit - Pressure Type

Huco Low-Pressure 12 Volt Fuel Pump Kit.

Hüco fuel pump for engines of up to some 160 BHP.

This is a "pressure type" pump, intended to placed near the fuel tank.

Please see HUCOPUMPFP02 in case that you require a "suction type" pump to be placed in the engine compartment of your vehicle.

Pump specification:

  • Flow rate 27.5 Gallons/hour / 125 liters/hour
  • Pressure: 2.1 PSI / 0.15 Bar
  • 12 - 14 Volt - negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol or Bio-Diesel

Kit includes:

  • Pump
  • Mounting bracket

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Thanks to its operating pressure of 2.1 PSI (some 0.15 Bar), this Huco pump does not require a pressure regulator which makes it a very cost-efficient proposition.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Huco Low-Pressure 12 Volt Fuel Pump Kit - Pressure Type

FPP01
Fuel Union for Huco Low-Pressure Fuel Pump

Fuel Union for Huco Low-Pressure Fuel Pump

Fuel Union for Huco Low-Pressure Fuel Pump.

Fits both varieties of the Hüco pump that we carry in our range.

Is supplied complete with O-Ring.

Suitable for fuel lines with 8 mm internal diameter.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

 

Fuel Union for Huco Low-Pressure Fuel Pump

SYTECPL031
Sytec Replacement Fuel Pump for Weber PL031 - Aston Martin Virage

Sytec Replacement Fuel Pump for Weber PL031 - Aston Martin Virage

Sytec replacement pump for the long obsolete Weber PL-031 fuel pump as used on, amongst others, the 1990 - 1996 Aston Martin Virage and Virage Volante.

The Weber PL031 is no longer produced yet it is a vital part of the car's fuel system.

Systec stepped in and produces this replacement pump in the USA.

Please note: this pump requires a high quality pre-filter to avoid contamination.

Specifications:

  • Fittings In:- Jic 6
  • Fittings Out:- Jic 6
  • Voltage:-12v
  • Flow Ltr/Hr (Max):- 348
  • Flow Ltr/Hr @ 3 Bar (44psi):- 270
  • Flow Ltr/Hr @ 5 Bar (73psi):- 222
  • Location To Tank (Mtrs) 0.6
  • Thread Size:-10x1mm SFT
  • Length (mm):- 160
  • Diameter (mm):- 43
  • Weight (Kg):- 0.46

Limited availability!

Sytec Replacement Fuel Pump for Weber PL031 - Aston Martin Virage

SYTECPL031
Sytec Replacement Fuel Pump for Weber PL031 - Ferrari F40

Sytec Replacement Fuel Pump for Weber PL031 - Ferrari F40

Here we have a Sytec replacement for the long obsolete Weber PL-031 fuel pump as used on, amongst others, the Ferrari F40.

The Weber PL031 is no longer produced yet it is a vital part of the car's fuel system.

Sytec stepped in and produces this replacement pump in the USA.

Please note: this pump requires a high quality pre-filter to avoid contamination.

Specifications:

  • Fittings In:- Jic 6
  • Fittings Out:- Jic 6
  • Voltage:-12v
  • Flow Ltr/Hr (Max):- 348
  • Flow Ltr/Hr @ 3 Bar (44psi):- 270
  • Flow Ltr/Hr @ 5 Bar (73psi):- 222
  • Location To Tank (Mtrs) 0.6
  • Thread Size:-10x1mm SFT
  • Length (mm):- 160
  • Diameter (mm):- 43
  • Weight (Kg):- 0.46

Limited availability!

Sytec Replacement Fuel Pump for Weber PL031 - Ferrari F40

FPA908R
74 Micron Replacement Facet GOLD-FLO Fuel Pump Filter Element

74 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

Replacement Facet Fuel Pump Filter Element in 74 Micron.

Fits the Facet GOLD-FLO and Interrupter series fuel pumps.

Suitable for gasoline and alcohol engines.

For Diesel engines and situations where a higher degree of filtration is required, please use the 200 Micron filter.

 

74 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

FPA908B
200 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

200 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

Replacement Facet Fuel Pump Filter Element in 200 Micron.

Fits the Facet GOLD-FLO and Interrupter series fuel pumps.

Especially designed for Diesel engines and situations where the standard filter of 74 Micron doesn't suffice.

 

 

200 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

FUELGAUGEKIT
In-Line Fuel Pressure Gauge Kit

In-Line Fuel Pressure Gauge Kit

In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

  • Sytec fuel pressure gauge (0 - 15 PSI / 0 - 1 Bar)
  • Pressure gauge adapter with connections for 8 mm fuel line
  • Brass blanking plug
  • Roll of our Superior Quality PTFE tape
  • 2 Stainless Steel jubilee clips for 8 mm fuel line

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on low-pressure fuel systems for carburetors.
A high-pressure set for fuel injection systems is in the making!

Spare, brass, blanking plugs can be found HERE.

In-Line Fuel Pressure Gauge Kit

FPG001
Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar.

Low pressure fuel pressure gauge.

Ideal for setting the pressure on systems with carburettors.

Can be used with the 85mm Filter King filter and pressure regulator or our Fuel Pressure Gauge Adapter.

Range:

  • 0 - 15 PSI
  • 0 - 1 Bar

Thread: 1/8th" tapered NPTF.

Note:
This gauge should only be used for setting-up and then be removed for normal running.
NOT suited for high-pressure (fuel injected) systems!

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

FGA100
Fuel Pressure Gauge Adapter

Fuel Pressure Gauge Adapter

In line fuel gauge adapter for pressure gauges with a thread size of 1/8th NPTF.

Suitable for flexible fuel lines with an internal diameter of 8 mm.

Machined from a solid billet of aluminum.

This adapter is supplied with brass blanking plug.

Can be used with the Sytec Low Pressure Fuel Pressure Gauge, the Webcon High Pressure Fuel Pressure Gauge or any other gauge with 1/8" tapered NPTF thread.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Spare, brass, blanking plugs can be found HERE.

Fuel Pressure Gauge Adapter

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch

AE119470
Disposable Fuel Filter - 6 mm and 8 mm

Disposable Fuel Filter - 6 mm and 8 mm

Newly arrived Disposable Fuel Filter - 6 mm and 8 mm

In-line, disposable, fuel filter.

The clever design of the unions makes it suitable for fuel lines with an internal diameter of both 6 mm and 8 mm.

The low cost makes it extremely well suited for vehicles that suffer from dirty fuel and dirty, or rusty, fuel tanks and where it would serve as a "first line of defense" against that dirt, thus protecting your valuable fuel pump, carburetor and engine from it.

Make sure to place the transparent bowl at the "fuel tank" end so that the dirt will collect there and it will be easy to visually inspect the condition of the filter.

Hose clamps suitable for your specific fuel line can be found HERE.

Disposable Fuel Filter - 6 mm and 8 mm

LOCTITE-542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

PLEASE NOTE !
This article is currently on order from our supplier.
We expect the delivery to our warehouse the second half of February 2018.
You can pre-order your now and now payment is needed until we actually ship to you.