Webcon Carburetor Products
Webcon Carburetor Products

Webcon Products

Webcon Carburetor Products

Webcon Carburetor Products

!
WFR150
Webcon Low-Pressure Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

Webcon Low-Pressure Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

Webcon High-Pressure Fuel Pressure Gauge 0 - 120 PSI / 0 - 8 Bar.

Ideal for setting the pressure on fuel injection systems.

Glycerin-filled for accurate reading under all circumstances.

Can be used with our Fuel Pressure Gauge Adapter.

Thread: 1/8th" tapered NPTF.

Range:

  • 0 - 120 PSI
  • 0 - 8 Bar

Note:
This gauge should only be used for setting-up and then be removed for normal running.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 542 Thread Sealant which will offer the added properties of protecting your connections from undoing themselves.

Webcon Low-Pressure Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

WFP150KIT
Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Webcon In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on low-pressure fuel systems for carburetors.

A high-pressure set for fuel injection systems can be found HERE.

Spare, brass, blanking plugs can be found HERE.

We advise Loctite 543 Thread Sealant to secure the gauge in the adapter.

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

WFR151
Webcon High-Pressure Fuel Pressure Gauge 0 - 120 PSI / 0 - 8 Bar

Webcon High-Pressure Fuel Pressure Gauge 0 - 120 PSI / 0 - 8 Bar

Webcon High-Pressure Fuel Pressure Gauge 0 - 120 PSI / 0 - 8 Bar.

Ideal for setting the pressure on fuel injection systems.

Glycerin-filled for accurate reading under all circumstances.

Can be used with our Fuel Pressure Gauge Adapter.

Thread: 1/8th" tapered NPTF.

Range:

  • 0 - 120 PSI
  • 0 - 8 Bar

Note:
This gauge should only be used for setting-up and then be removed for normal running.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 542 Thread Sealant which will offer the added properties of protecting your connections from undoing themselves.

Webcon High-Pressure Fuel Pressure Gauge 0 - 120 PSI / 0 - 8 Bar

WFP151KIT
Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Webcon In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on high-pressure injection systems.

A low-pressure set for carbureted systems can be found HERE.

Spare, brass, blanking plugs can be found HERE.

We advise Loctite 543 Thread Sealant to secure the gauge in the adapter.

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch

WCAFB386
Bowler Hat Airfilter for Weber DMTL carburetors

Bowler Hat Airfilter for Weber DMTL carburetors

Great looking "Bowler Hat" style airfilter with chromed mesh and baseplate to fit the Weber DMTL carburetors.

Foam insert.

Made by Webcon.

The total package contains the following:

  • Breather pipe adapter
  • Blanking Plug
  • Base plate gasket
  • Fixing material as per the photograph

The total height is circa 60 mm.

Please note that the base plate will need slight alteration to make it fit onto a Land Rover with 32/34 Weber DMTL.

Bowler Hat Airfilter for Weber DMTL carburetors

WCAFB386
Bowler Hat Airfilter for Weber DMTR carburetors

Bowler Hat Airfilter for Weber DMTR carburetors

Great looking "Bowler Hat" style airfilter with chromed mesh and baseplate to fit the Weber DMTR carburetors.

Foam insert.

Made by Webcon.

The total package contains the following:

  • Breather pipe adapter
  • Blanking Plug
  • Base plate gasket
  • Fixing material as per the photograph

The total height is circa 60 mm.

Please note that the base plate will need slight alteration to make it fit onto a Land Rover with 32/34 Weber DMTL.

Bowler Hat Airfilter for Weber DMTR carburetors

WCAFB386
Bowler Hat Airfilter for Weber DFTH carburetors

Bowler Hat Airfilter for Weber DFTH carburetors

Great looking "Bowler Hat" style airfilter with chromed mesh and baseplate to fit the Weber DFTH carburetors.

Foam insert.

Made by Webcon.

The total package contains the following:

  • Breather pipe adapter
  • Blanking Plug
  • Base plate gasket
  • Fixing material as per the photograph

The total height is circa 60 mm.

Please note that the base plate will need slight alteration to make it fit onto a Land Rover with 32/34 Weber DMTL.

Bowler Hat Airfilter for Weber DFTH carburetors

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker