Alfa Romeo 105 Series Carburetor Service Kits
Alfa Romeo 105 Series Carburetor Service Kits

Alfa Romeo 105-Series

Alfa Romeo 105 Series Carburetor Service Kits.

On this page you will find the service kits for the 105 series that we can supply.

If the service kit that you're looking for isn't listed yet, please contact us by email as there is a good chance that we can help you anyway.

Our Contact Page can be found HERE.

Alfa Romeo 105 Series Carburetor Service Kits

!
Nordrubbers
Complete Set of Carburetor Mounts for Alfa Romeo Nord Engines 105 115 and 116 series

Complete Set of Carburetor Mounts for Alfa Romeo Nord Engines 105 115 and 116 series

Here we have a complete set of parts required for a "Carb Mount Change" on Alfa Romeo's famous Nord engines.

Suitable for all Nord engines with 40 mm carburettors.

Suitable for the Weber DCOE 40, the Dellorto DHLA 40 and the Solex ADDHE 40 carbs.

These mounts are of the highest quality that we can source at this moment.

The difference in quality can be found in the "flatness" of both sides the flanges.

After the flanges are vulcanized together with rubber, they are planed on a lathe to create an absolutely flat surface. For this reason, the studs are included but still need to be installed.

As visible in the pictures, the set consists of 1 "double" mount and 2 "single" mounts.

Additionally, this set also comprises an inlet-manifiold-to-cylinder-head gasket, 4 manifold-to-mount gaskets and 4 mount-to-carburetor gaskets so that you have everything you need to replace you leaking mounts.

The photo will be corrected to show the correct number of gaskets included in this set.

Complete Set of Carburetor Mounts for Alfa Romeo Nord Engines 105 115 and 116 series

AS1FU202
Rebuild kit for Fispa Fuel Pressure Regulator Kit WITH Pin

Rebuild kit for Fispa Fuel Pressure Regulator Kit WITH Pin

This is a complete overhaul kit for the Fispa Fuel Pressure Regulator.

Please note that Fispa has produced at least two different versions over the years:

  1. The version WITHOUT a pin on the center of the diaphragm
  2. This version here WITH a pin on the center of the diaphragm

The difference between the two will be clear from this picture:
Rebuild kit for Fispa Fuel Pressure Regulator Kit WITH Pin

There are more differences than just the pin but the pin is the best indicator for which kit you need.

The set with the diaphragm WITHOUT pin can be found HERE.

Officially, this set suits both the Fispa FB43 and FRB11 fuel filters with build-in pressure regulator.

The bolt pattern is as follows: circa 33 mm heart-to-heart and about 42 mm across (diagonally).

This set is E10- and bio-fuel resistant.

Rebuild kit for Fispa Fuel Pressure Regulator Kit WITH Pin

AS1FU205
Rebuild kit for Fispa Fuel Pressure Regulator Kit WITHOUT Pin

Rebuild kit for Fispa Fuel Pressure Regulator Kit WITHOUT Pin

This is a complete overhaul kit for the Fispa Fuel Pressure Regulator.

Please note that Fispa has produced at least two different versions over the years:

  1. The version WITH a pin on the center of the diaphragm
  2. This version here WITHOUT a pin on the center of the diaphragm

The difference between the two will be clear from this picture:
Rebuild kit for Fispa Fuel Pressure Regulator Kit WITOUT Pin

There are more differences than just the pin but the pin is the best indicator for which kit you need.

The set with the diaphragm WITH pin can be found HERE.

Officially, this set suits both the Fispa FB43 and FRB11 fuel filters with build-in pressure regulator.

The bolt pattern is as follows: circa 33 mm heart-to-heart and about 42 mm across (diagonally).

This set is E10- and bio-fuel resistant.

Rebuild kit for Fispa Fuel Pressure Regulator Kit WITHOUT Pin

52528
(102) Original Gasket Kit for 2 Dellorto DHLA Carburetors

(102) Original Gasket Kit for 2 Dellorto DHLA Carburetors

Original Dellorto DHLA Gasket Kit.

Factory original Dellorto kit.

Contains the gaskets, rings and o-rings to freshen up 2 carburettors.

Serves as an alternative to the more complete, hence more expensive, full service kit.

Can be used for the Dellorto DHLA40, DHLA45 and DHLA48.

This is item number 102 in the drawing.

Please note that this is set is only suited for normally aspirated engines, NOT for turbo-charged engines!

 

(102) Original Gasket Kit for 2 Dellorto DHLA Carburetors

DHLASK1
(102) Original Service Kit for 1 Dellorto DHLA Carburetor

(102) Original Service Kit for 1 Dellorto DHLA Carburetor

Service kit for the Dellorto DHLA carburetor.

Factory original Dellorto kit.

Contains the parts to service 1 carburetor.

When ordering, please select the required needle valve size through the drop-box above.
You can check the size of your current needle valve on the bronze base where it should be stamped.
Unless you have modified your engine and are convinced that a different, usually bigger, size is required, we advise against experimenting with needle valve sizes.

The standard fitment sizes were:

  • DHLA40 - size 150
  • DHLA45 - size 170
  • DHLA48 - size 225
  • Gravity-fed systems such as motorcycles and high-consumption rotary engines: size 350

The set consists of the following parts:

  • 1 Pump diaphragm
  • 1 Pump diaphragm spring
  • 1 Needle valve, Viton tipped - select the required size when ordering
  • 1 Fuel filter
  • 1 Main spindle return spring
  • Complete gasket set
  • Various rubber (Viton) o-rings
  • Various aluminum washers
  • Various fiber washers

This is item number 102 in the drawing.

Attention: this set is NOT suited for TURBO-applications! For turbo-charged cars, please use the appropriate service kit which you can find HERE.

(102) Original Service Kit for 1 Dellorto DHLA Carburetor

DHLACSK1
(102) Budget Service Kit for 1 Dellorto DHLA Carburetor

(102) Budget Service Kit for 1 Dellorto DHLA Carburetor

Budget service kit for a Dellorto DHLA40 or DHLA45 carburetor.

Contains after-market parts.

Consists of the following parts to service 1 carburetor:

  • 1 Pump diaphragm
  • 1 Needle valve, brass-tipped - size 150 for DHLA40 or size 175 for the DHLA45
    Please select the desired size through the drop-box above.
  • Gasket set
  • Various rubber (Viton) o-rings
  • Various aluminum washers
  • Various fiber washers

This is item number 102 in the drawing.

(102) Budget Service Kit for 1 Dellorto DHLA carburetor

ADDHE
Service Kit for 2 x Solex 40 ADDHE carburetors

Service Kit for 2 x Solex 40 ADDHE carburetors

Service kit for the Solex ADDHE 40 carburetor.

Contains the parts to service 2 carburettors.

Consists of the following parts:

  • Various gaskets
  • 2 Pump Diaphragms
  • 2 Needle Valves
  • 4 carburetor-to-inlet-manifold gaskets
  • Various rubber o-rings
  • Various aluminum washers

This is a Carburetor City carburettor service set, Made in Italy to the highest standards.

Service Kit for 2 Solex 40 ADDHE carburetors

PM10708
(29) Replacement Diaphragm for Solex 40 DDH carburetors

(29) Replacement Diaphragm for Solex 40 DDH carburetors

Replacement diaphragm for the pump of the Solex DDH series carburetors as often used by Alfa Romeo.

Suitable for the following variations of the DDH:

  • Solex 40 DDH 3
  • Solex 40 DDH 5
  • Solex 40 DDH 7
  • Solex 40 DDH 8

Required quantity per carburetor: 1

This is number 29 in the drawing.

This is a Carburetor City diaphragm as Solex no longer produces these diaphragms themselves.

(29) Replacement Diaphragm for Solex 40 DDH carburetors

PMS102
Service Kit for 2 x Solex 40 DDH 3 carburetors for Alfa Romeo Giulia 1600 Super

Service Kit for 2 x Solex 40 DDH 3 carburetors for Alfa Romeo Giulia 1600 Super

Service kit for the Solex 40 DDH 3 carburetors as used on, amongst others, the Alfa Romeo Giulia 1600 Super.

Although these carburetors were originally specified for the above cars, they could have been transplanted onto other cars and engines so the range of vehicles that these service sets might fit is much broader.

Alternatively, it is very well possible that your car is no longer be equipped with the carburetor that it left the factory with.

So, we advise you to check carefully if the parts in the picture will fit your carburetor.

In some extreme cases, it might be necessary to disassemble your carburetor to compare the individual parts prior to purchase.

Contains the parts to service 2 carburettors.

Consists of the following parts:

  • Various gaskets
  • 2 Pump Diaphragms
  • 2 Needle Valves Size 1.6
  • 4 Inlet Plenum Gaskets
  • Various rubber o-rings
  • Various fiber washers
  • Various aluminum washers

This is a Carburetor City carburettor service set, Made in Italy to the highest standards.

Service Kit for 2 x Solex 40 DDH 3 carburetors for Alfa Romeo Giulia 1600 Super

PMS102
Service Kit for 2 x Solex 40 DDH 5-7-8 carburetors for Alfa Romeo 105 Series 1750 and 2000

Service Kit for 2 x Solex 40 DDH 5-7-8 carburetors for Alfa Romeo 105 Series 1750 and 2000

Service kit for the Solex 40 DDH carburetors, versions 5, 7 and 8, as used on, amongst others, the Alfa Romeo 105 Series Berlina and GTV 1750 and 2000.

Although these carburetors were originally specified for the above cars, they could have been transplanted onto other cars and engines so the range of vehicles that these service sets might fit is much broader.

Alternatively, it is very well possible that your car is no longer be equipped with the carburetor that it left the factory with.

So, we advise you to check carefully if the parts in the picture will fit your carburetor.

In some extreme cases, it might be necessary to disassemble your carburetor to compare the individual parts prior to purchase.

Contains the parts to service 2 carburettors.

Consists of the following parts:

  • Various gaskets
  • 2 Pump Diaphragms
  • 2 Needle Valves Size 1.6
  • 4 Inlet Plenum Gaskets
  • Various rubber o-rings
  • Various fiber washers
  • Various aluminum washers

This is a Carburetor City carburettor service set, Made in Italy to the highest standards.

Service Kit for 2 x Solex 40 DDH 5-7-8 carburetors for Alfa Romeo 105 Series 1750 and 2000

PMS101
Rebuild Kit for Solex 32 PAIA 7-15 carburetors for Alfa Romeo Giulia 1300 TI

Rebuild Kit for Solex 32 PAIA 7-15 carburetors for Alfa Romeo Giulia 1300 TI

Rebuild kit for the Solex 32PAIA 7-15 carburetors as used on, amongst others, the:

  • 1290 cc Alfa Romeo Giulia 1300 TI

Contains the following parts to service 1 carburettor:

  • Various gaskets
  • Pump diaphragm
  • Nitrile pump housing gasket
  • Needle Valve Size 150
  • Various copper washers
  • Various fiber washers

For the exact contents, please see the photograph.

This is a Carburetor City service kit of superior Italian manufacture.

Rebuild Kit for Solex 32 PAIA 7-15 carburetors for Alfa Romeo Giulia 1300 TI

CCR9950
Elaborate Rebuild Kit for Solex 32 PAIA carburetors

Elaborate Rebuild Kit for Solex 32 PAIA carburetors

This is our most elaborate rebuild kit for the Solex 32PAIA carburetors.

It contains the following parts to service 1 carburettor:

  • Manifold gasket
  • Float chamber gasket
  • Airfilter gasket
  • Complete pump diaphragm + extra sheets
  • Nitrile pump housing gasket
  • Choke housing gasket
  • Needle Valve Size 175
  • 2 Throttle shaft seals
  • 4 Brass throttle shaft bushings
  • 2 Throttle valve discs - 32 mm - 8°
  • 4 Throttle valve screws
  • Various copper washers
  • Various fiber washers
  • Rubber O-ring

For the exact contents, please see the photograph.

This is a Carburetor City service kit of superior Italian manufacture.

Elaborate Rebuild Kit for Solex 32 PAIA carburetors

PMW100
Rebuild kit for 2 x Italian Weber 45 DCOE 14 carburetors for Alfa Romeo Giulia TI Super

Rebuild kit for 2 x Italian Weber 45 DCOE 14 carburetors for Alfa Romeo Giulia TI Super

Rebuild kit for 2 x Italian Weber 45 DCOE 14 carburetors as used on the famous Alfa Romeo Giulia TI Super.

Comprehensive service kit for the ITALIAN-made (!) Weber DCOE carburetor in 45 mm version.
You can recognize these by the text "Made in Italy" on the top cover.

Contains the following parts to service 2 carburetor:

  • Fuel inlet filters
  • Needle valves in size 150
  • Comprehensive gasket set
  • Pump jet washers
  • Various aluminum washers
  • Various fiber washers

Please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.

This is a Carburetor City service kit of outstanding Italian manufacture.

Rebuild kit for 2 x Italian Weber 45 DCOE 14 carburetors for Alfa Romeo Giulia TI Super

WE436
Comprehensive service kit for 1 x Italian Weber DCOE carburetor

Comprehensive service kit for 1 x Italian Weber DCOE carburetor

Comprehensive service kit for the ITALIAN-made (!) Weber DCOE carburetor.

This set is suitable for the following versions of the DCOE:

  • Weber 38 DCOE
  • Weber 40 DCOE
  • Weber 42 DCOE
  • Weber 45 DCOE
  • Weber 48 DCOE

For this service kit, the difference between the above versions is made by the size of the needle valve.
The original size can be found stamped in the brass needle valve seat which is mounted in the top cover of the carburetor.

We can offer the following sizes which you can select through the drop-box above:

  • 150
  • 175
  • 200
  • 225
  • 250
  • 300

Contains the following parts to service 1 carburetor:

  • Needle valve
  • Full gasket set
  • Pump jet washers
  • Fuel inlet filter
  • Float pivot pin
  • Mixture screws x 2, long taper for better adjustment
  • Throttle return spring

Suitable for the original Italian Weber DCOE's.
You can recognize these by the text "Made in Italy" on the top cover.

For the current production Spanish-made DCOE's, please use the WE437 kit.

Comprehensive service kit for 1 x Italian Weber DCOE carburetor

DCOESK175NV
Budget service kit for 1 x Italian Weber DCOE carburetor

Budget service kit for 1 x Italian Weber DCOE carburetor

Budget service kit for the ITALIAN-made (!) Weber DCOE versions 38, 40, 42, 45 and 48.

Contains all required parts to service 1 carburetor.

Consists, amongst others, of the following parts:

  • 175 size Needle valve
  • Full gasket set
  • Fuel inlet filter
  • Float pivot pin
  • Parts diagram and float level setting instructions

Suitable for the original Italian Weber DCOE's.

For the current production Spanish-made DCOE's, please use the WE437 kit.

Budget service kit for 1 x Italian Weber DCOE carburetor

DCOE GASKET KIT
Gasket kit for 1 x Italian Weber DCOE carburetor

Gasket kit for 1 x Italian Weber DCOE carburetor

This is a simple gasket kit for the Weber DCOE 40 carburetors.

Contains all required gaskets seals and rings to freshen-up 1 carb.

Suitable for the original Italian-made Weber DCOE's.

 

 

Gasket kit for 1 x Italian Weber DCOE carburetor

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15 MM
  • 0.25 MM
  • 0.4 MM
  • 0.8 MM
  • 1.6 MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

GREENFUEL8MM-50cm
Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

Alternatively, this hose simply looks great when used with the "Endless band & Buckle" hose clamps like in the photo.

Please note:
This hose is NOT E10 resistant.
Do not use this hose if you are not able to avoid using Ethanol-containing fuels.

Italian style clear green fuel line hose with 8 mm inner diameter

gatestextiel8mm
Gates textile covered fuel line hose with 8 mm inner diameter

Gates textile covered fuel line hose with 8 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 0.5 meter.

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

Gates textile covered fuel line hose with 8 mm inner diameter

2134.0600
Cohline E10-resistant fuel line hose with 8 mm inner diameter

Cohline E10-resistant fuel line hose with 8 mm inner diameter

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose.

This fuel hose has an actual inner diameter of 7.5 mm and 13.5 mm outer diameter and therewith a nice and tight fit for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

This hose uses 11 - 13 mm jubilee clips.

Cohline E10-resistant fuel line hose with 8 mm inner diameter

norm5mm
Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide.

Again one of those items that allows you to put the finishing touches on a restoration!

This is the famous "endless band hose clamp with buckle" that was used throughout the 1950's, 1960's and 1970's in the car industry.

Unfortunately, these band clamps are only suitable for one-time use and are discarded after removing them.

Over the years, these clamps have become harder and harder to find but we managed to find a source!

We are selling these in sets.

Such a set consist of the following:

  • Approximately 100 cm Zinc-plated band, 5 millimeters wide
  • 3 buckles

This way, you have roughly a foot (or 33 cm) of band per clamp / buckle which is more than enough for regular applications.

Thanks to the generous length of band, there is virtually no limit to the diameter or circumference of the clamp that you wish to apply although these were usually applied to small diameter fuel lines.

Please note that this style of clamping is NOT suitable for steel-braided lines.

Endless Band Hose Clamp with Buckle - 5 mm wide

jubilee11-13
11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

2134.01.0600
Cohline E10-resistant fuel line hose with 8 mm inner diameter and steel braiding

Cohline E10-resistant fuel line hose with 8 mm inner diameter and steel braiding

This is the top-of-the-line Cohline, steel-braided E10-resistant, flexible fuel line / hose.

This fuel hose has an 8 mm inner diameter and 16 mm outer diameter and is therewith suitable for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

 This fuel line uses 15 - 17 mm jubilee clips.

Cohline E10-resistant fuel line hose with 8 mm inner diameter and steel braiding

jubilee15-17
15 - 17 mm Stainless Steel Jubilee Clip Hose Clamp

15 - 17 mm Stainless Steel Jubilee Clip Hose Clamp

15 - 17 mm Stainless Steel Jubilee Clip Hose Clamp.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to a well-cared for "under the hood" look.

It is rated for between 15 - 17 mm external diameter flexible hose / line.

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

15 - 17 mm Stainless Steel Jubilee Clip Hose Clamp

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

G4053
Gunson Carbalancer Carburetor Synchronizing Tool - G4053

Gunson Carbalancer Carburetor Synchronizing Tool - G4053

Gunson Car Balancer.

Internal combustion engines use a mixture of air and petrol to generate their power.

The performance therefore is influenced by the air flowing into it and the petrol that is metered out by the carburettor.

Unless the air flow in Twin or Multiple carburettors is correctly set, the correct mixture adjustment is unlikely to be achieved and this is the simplest tool to achieve that.

Suitable for use on SU, Solex, Auto-Lite (Fomoco), Stromberg, Weber and Zenith and can be adjusted to fit most carburettors including sidedraft, downdraft with air intakes (Venturi) from 25 mm to 67 mm (1”-2”) diameter

  • Easy read scale indicates the air flow and allows adjustment to optimum efficiency
  • Provides smoother and better acceleration
  • Carbalancer can be adjusted to fit most carburettors
  • Easy to follow instructions

The user manual for the Gunson Carbalancer, in English, can be downloaded HERE.

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Carbalancer Carburetor Synchronizing Tool - G4053

MANOMETER2
2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easily read scale
  • Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off adapters can be found HERE.

2 Column Manometer - Synchrometer Carbtune Pro

MANOMETER4
4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer / Synchronometer.

This is the New Carbtune Pro, the essential tool for balancing multiple carburettors.

  • The column type scales give a superior resolution compared to dial type gauges
  • Comes complete with 4 x 5 mm and 4 x 6 mm brass adapters and 4 silicone rubber hoses.
  • The supplied adapters will suit the Dellorto DHLA and Weber DCOE carburetors and many motorcycle carburettors.
  • The stainless steel columns indicate the vacuum that each cylinder draws
  • There is no calibration or set-up required
  • Made out of a high-impact plastic casing and scale tubes - not glass to prevent breakage
  • The built-in dampers reduce fluctuations
  • Supplied with full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off adapters can be found HERE.

4 Column Manometer - Synchrometer Carbtune Pro

9679
Brass vacuum take-off adapter for carburetors and manifolds

Brass vacuum take-off adapter for carburetors and manifolds

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Thread: 5 mm x 0.8

Overall length: 20 mm

Also fits the Weber DCOE series carburettors and Solex ADDHE.

Brass vacuum take-off adapter for carburetors and manifolds

SYNCHRONOMETER
Synchrometer airflow meter for carburetors

Synchrometer airflow meter for carburetors

Synchrometer airflow meter for various carburetors.

Pushes into the trumpet / ram pipe / velocity stack or throat to measure the airflow to enable you to balance multiple carburettors.

  • Instructions included
  • The original genuine high quality German made product
  • Can be used for all Weber DCOE and IDF and Dellorto DHLA, DRLA carbs with round intakes or trumpets
  • Can also be used with motorcycle carburetors with round intakes

Total length of unit 121mm

Rubber cone dimensions:
Small end diameter 40mm
Large end diameter 55mm
Length of cone 36mm

Synchrometer airflow meter for carburetors

4GAUGESYNCHRO
4 Gauge Carburetor Synchronizing Balancing Tool

4 Gauge Carburetor Synchronizing Balancing Tool

Carburetor Vacuum Synchronizer Set.

4 gauge tool kit, mounted on a solid metal frame for easy reading.

The vacuum gauges range from 0 to -1 bar.

This measurement tool was designed to check and adjust motorcycles and cars with 2, 3 or 4 carburetors.

Each of the gauges is equipped with a damper to obtain stable readings.

The gauges allow to measure the vacuum in each of the gas tubes so you can make direct adjustments to obtain a smooth running engine.

The set comes with all necessary parts like:

  • 4 92 mm gauges fixed on a metal frame
  • 4 rubber hoses 8 x 5 x 750 mm
  • 4 hose clamps
  • 4 adapters M6 x 0.75 - length 53 mm
  • 4 adapters M6 x 1.00 - length 60 mm
  • 4 adapters M5 x 0.75 - length 98 mm
  • 4 adapters M6 x 0.75 - length 170 mm
  • 1 extension 6 x 55 mm
  • Red, blow-molded carry case

Fits the Dellorto DHLA, Dellorto DHLB, Dellorto DRLA, Dellorto PHF, Weber DCOE, Weber DCOM Solex ADDHE and many many more. Please check the list of adapters to see if they fit your particular carburetors.

4 Gauge Carburetor Synchronizing Balancing Tool

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker

G4125
Gunson Digital Exhaust Gas and CO Tester - G4125

Gunson Digital Exhaust Gas and CO Tester - G4125

The Gunson Digital Exhaust Gas and CO Tester is the perfect (and affordable !) tool for the DIY mechanic to measure and adjust the CO-percentage in the exhaust gases of cars, motorcycles, boats etc equipped with a petrol-driven internal combustion engines.

Allows you to measure the current CO-percentage after which you can adjust it to the required level.

This system is equipped with a pulse pump and is suitable for both leaded and unleaded petrol / gasoline.

The tester will calibrate itself in the open air, has no moving parts to reduce wear and tear and has no filters.

Measures the CO % to 0,5 % accurately throughout the range.

Power: 12 Volt car- or motorcycle battery.

The set comprises the following:

  • The Gastester with box
  • Puls pump with water trap
  • Metal exhaust probe
  • 3 Flexibel pipes
  • Operating Manual in English

If you require the owner's manual again, you can download it HERE.

Additional instructions on adjusting the Gastester, in English, can be downloaded HERE.

This is a short instruction video, again in English:

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Digital Exhaust Gas and CO Tester - G4125