Dellorto PHBH and PHBL Carburetor Parts
Dellorto PHBH and PHBL Carburetor Parts

Dellorto PHBH and PHBL Parts

Dellorto PHBH and PHBL Carburetor Parts.

On this page you will find all currently available parts for the Dellorto PHBH and PHBL range carburetors.

Click HERE for an exploded view drawing of the Dellorto PHBH and PHBL series.

The numbers in the drawing correspond to the numbers in brackets at the beginning of the article description.

Click HERE for instructions on how to set the float level of the Dellorto PHBH and PHBL.

Click HERE for an overview of the Dellorto D-Type needles.

Click HERE for an overview of the Dellorto W & X-Type needles.

We are still very much expanding our parts offerings for these carburettors so please contact us by email if the part that you are looking for is not yet listed.

Dellorto PHBH and PHBL Carburetor Parts

!
DELLR4149
New Dellorto PHBH 28 FD carburetor for Honda 125 NSR

New Dellorto PHBH 28 FD carburetor for Honda 125 NSR

Factory-new Dellorto PHBH 28FD carburetor for the Honda NSR 125.

This carburetor is the original equipment on Honda NSR Raiden 125cc, but can be re-jetted to suit any engine.

It features a 42 mm plain air intake connection and 36 mm rubber sleeve type engine connection.

Comes equipped with an oil feed connection.

Cable type choke mechanism fitted but a lever type can be fitted if requested.

The standard jetting is as follows:

  • 40 Slide
  • X84 Needle
  • 268EB Atomiser
  • 135 Main jet
  • 40 Idle jet
  • BF3 Idle emulsion tube
  • 65 Power jet
  • 60 Choke jet
  • 300 Needle valve
  • 9010.1 Float - 9.5 grams

New Dellorto PHBH 28 FD carburetor for Honda 125 NSR

9477
(2) X-Type Needle for Dellorto PHBH carburetors

(2) X-Type Needle for Dellorto PHBH carburetors

X-Type needle for the Dellorto PHBH carburetors.

Original Dellorto!
Only original Dellorto Needles are marked with the famous "Inc" logo!

These needles come in many different varieties of which you can find an overview HERE.

In stock in variety:

  • X6
  • X8
  • X15
  • X17

Please contact us by email if you require other varieties.

Required quantity per carburettor: 1

This is item number 2 in the drawing.

(2) X-Type Needle for Dellorto PHBH carburetors

2265
(2) D-Type Needle for Dellorto PHBL carburetors

(2) D-Type Needle for Dellorto PHBL carburetors

D-Type needle for the Dellorto PHBL carburetors.

Where possible, we only supply original Dellorto needles marked with the famous diamond-shaped "Inc" logo. However, sizes that are no longer supplied by Dellorto themselves are manufactured for us at the exact same high standards.

These needles come in many different varieties of which you can find an overview HERE.

In stock in variety:

  • D1
  • D31
  • D36
  • D52

Please contact us by email if you require other varieties.

Required quantity per carburettor: 1

This is item number 2 in the drawing.

(2) D-Type Needle for Dellorto PHBL carburetors

9542
Bush for DR Series Atomizer for Dellorto PHBH carburetors

Bush for DR Series Atomizer for Dellorto PHBH carburetors

Atomiser Bush for Dellorto PHBH carburetors.

This bush is a push-fit into the body of the carburettor and is the part in which the atomiser screws.

It is specific for the DR-Series Atomisers.

Required quantity per carburettor: 1

This is item is NOT in the drawing.

Bush for DR Series Atomizer for Dellorto PHBH carburetors

9198
Bush for AV, BN and AS Series Atomizer for Dellorto PHBH carburetors

Bush for AV, BN and AS Series Atomizer for Dellorto PHBH carburetors

Atomiser Bush for Dellorto PHBH carburetors.

This bush is a push-fit into the body of the carburettor and is the part in which the atomiser screws.

It is specific for the AV, BN and AS-Series Atomisers.

Required quantity per carburettor: 1

This is item is NOT in the drawing.

Bush for AV, BN and AS Series Atomizer for Dellorto PHBH carburetors

8358
(3) K Type Main Emulsion Tube for Dellorto PHBL carburetors

(3) K Type Main Emulsion Tube for Dellorto PHBL carburetors

K Type Main Emulsion Tube for Dellorto PHBL carburetors.

Available from our stock as version K266.

Other versions are available on application.

Required quantity per carburettor: 1

This is item number 3 in the drawing.

 

 

(3) K Type Main Emulsion Tube for Dellorto PHBL carburetors

10174
(4) BN Type Main Emulsion Tube for Dellorto PHBH carburetors

(4) BN Type Main Emulsion Tube for Dellorto PHBH carburetors

BN Type Main Emulsion Tube for Dellorto PHBH carburetors.

Available from our stock as version BN270.

Other versions are available on application.

When not already present, the use of this emulsion tube requires the use of Bush 9198.

Required quantity per carburettor: 1

This is item number 4 in the drawing.

(4) BN Type Main Emulsion Tube for Dellorto PHBH carburetors

10532
(5) CD1 Type Idle Emulsion Tube for Dellorto PHBH and PHBL carburetors

(5) CD1 Type Idle Emulsion Tube for Dellorto PHBH and PHBL carburetors

CD1 Type Idle Emulsion Tube for Dellorto PHBH and PHBL carburetors.

Only still available as version CD1.

Required quantity per carburettor: 1

This is item number 5 in the drawing.

 

 

(5) CD1 Type Idle Emulsion Tube for Dellorto PHBH and PHBL carburetors

6413
(6) Main jet for Dellorto PHBH and PHBL carburetors

(6) Main jet for Dellorto PHBH and PHBL carburetors

Main jet for the Dellorto PHBH and PHBL carburetors.

Where possible, we only supply original Dellorto jets marked with the famous diamond-shaped "Inc" logo. However, sizes that are no longer supplied by Dellorto themselves are manufactured for us at the exact same high standards.

In stock in sizes:

  • 50
  • 52
  • 54
  • 56
  • 58
  • 60
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 105
  • 108
  • 110
  • 115
  • 116
  • 118
  • 120
  • 122
  • 124
  • 125
  • 126
  • 130
  • 132
  • 135
  • 140
  • 145
  • 150
  • 155
  • 160
  • 165
  • 170
  • 172
  • 175
  • 180
  • 182
  • 185
  • 190
  • 195
  • 198
  • 200
  • 205
  • 210
  • 215

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 6 in the drawing.

(6) Main jet for Dellorto PHBH and PHBL carburetors

1486
(7) Idle Jet for Dellorto PHBH and PHBL carburetors

(7) Idle Jet for Dellorto PHBH and PHBL carburetors

Factory original idle jet for the Dellorto PHBH and PHBL carburetors.

Where possible, we only supply original Dellorto jets marked with the famous diamond-shaped "Inc" logo. However, sizes that are no longer supplied by Dellorto themselves are manufactured for us at the exact same high standards.

Available from our stock in sizes:

  • 33
  • 35
  • 36
  • 38
  • 40
  • 45
  • 48
  • 50
  • 53
  • 55
  • 57
  • 58
  • 60
  • 62
  • 65
  • 67
  • 72
  • 80
  • 82
  • 84
  • 86
  • 88
  • 90
  • 91
  • 92
  • 95
  • 98
  • 100
  • 108
  • 110
  • 112
  • 115
  • 118
  • 120

Most other sizes are available on special order. Please contact us by email with your exact requirements.

Required quantity per carburettor: 1

This is item number 7 in the drawing.

(7) Idle Jet for Dellorto PHBH and PHBL carburetors

7746
(8) Choke or Starter Jet for Dellorto PHBL and PHBH carburetors

(8) Choke or Starter Jet for Dellorto PHBL and PHBH carburetors

Choke (or starter) jet for the Dellorto PHBH and PHBL carburetors.

Where possible, we only supply original Dellorto jets marked with the famous diamond-shaped "Inc" logo. However, sizes that are no longer supplied by Dellorto themselves are manufactured for us at the exact same high standards.

Available from stock in size:

  • 45
  • 50
  • 55
  • 60
  • 65
  • 70
  • 75
  • 80
  • 85
  • 90
  • 100

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 8 in the drawing.

(8) Choke or Starter Jet for Dellorto PHBL and PHBH carburetors

12202
(9) Genuine Viton-Tipped Needle Valve for Dellorto PHBH and PHBL carburetors

(9) Genuine Viton-Tipped Needle Valve for Dellorto PHBH and PHBL carburetors

This is the single dellorto needle valve needle for the PHBH and PHBL carburetors.

Genuine Dellorto part, Viton-tipped!

Only genuine Dellorto needles are marked with the diamond shaped "Inc" logo!

This needle is used in the seats with size 250 and 270 of our set which you can find HERE.

It is Viton-tipped and spring-loaded.

The body measures 4 mm square.

The length of the body + Viton tip measures 14.95 mm.

The overall length is 18.75 mm.

Please note that this needle will NOT fit the seats of sizes 300, 350 and 400.

Required quantity per carburettor: 1

This is item number 9 in the drawing.

(9) Genuine Viton-Tipped Needle Valve for Dellorto PHBH and PHBL carburetors

NV
(9) Viton-Tipped Needle Valve Assembly for Dellorto PHBH en PHBL carburetors - Spring Loaded

(9) Viton-Tipped Needle Valve Assembly for Dellorto PHBH en PHBL carburetors - Spring Loaded

Dellorto needle valve, seat and fiber washer for the PHBH and PHBL carburetors.

Genuine Dellorto part, Viton-tipped!

Only genuine Dellorto needles are marked with the diamond shaped "Inc" logo!

Available in size:

  • 150
  • 170
  • 200
  • 225
  • 250
  • 270
  • 300
  • 350
  • 400

Please note that this the spring-loaded version.
For the solid version, please see article number 9436.

Required quantity per carburettor: 1

This is item number 9 in the drawing.

The single needle (so without seat) for sizes 250 and 275 is also available and can be found HERE.

(9) Viton-Tipped Needle Valve Assembly for Dellorto PHBH en PHBL carburetors - Spring Loaded

9436
(9) Viton-Tipped Needle Valve Assembly for Dellorto PHBH en PHBL carburetors - Solid

(9) Viton-Tipped Needle Valve Assembly for Dellorto PHBH en PHBL carburetors - Solid

Dellorto needle valve, seat and fiber washer for the PHBH and PHBL carburetors.

Genuine Dellorto part, Viton-tipped!

Only genuine Dellorto needles are marked with the diamond shaped "Inc" logo!

Available in size:

  • 150
  • 170
  • 200
  • 225

Please note that this is the solid version.
For the spring-loaded version, please article number NV.

Required quantity per carburettor: 1

This is item number 9 in the drawing.

(9) Viton-Tipped Needle Valve Assembly for Dellorto PHBH en PHBL carburetors - Solid

9010
(10) Double plastic float for Dellorto PHBH and PHBL carburetors

(10) Double plastic float for Dellorto PHBH and PHBL carburetors

This is the one-piece (or double if you want) plastic, float for the Dellorto PHBH and PHBL carburetors.

Please note that these floats were originally ONLY made in black plastic and a stainless steel connector but that Dellorto is replacing these with a one-piece white plastic version on a running basis.

Although the weight of the black and white versions differs, the individual versions have the same buoyancy i.e. you can replace a black 9010.2 by a white 9010.2 without any problems.

We strongly advise against experimenting with different versions.

We will supply you with the current version.

Available in the following versions:

  • 9010.1 (currently white, one-piece)
  • 9010.2 (currently white, one-piece)
  • 9010.3 (currently black, steel connector)

Required quantity per carburettor: 1

This is item number 10 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHBH and PHBL.

(10) Double plastic float for Dellorto PHBH and PHBL carburetors

1476A
(11) Rubber Cable Boot for Dellorto PHBH and PHBL carburetors

(11) Rubber Cable Boot for Dellorto PHBH and PHBL carburetors

Rubber cable cap for both the choke cable as well as the throttle cable on the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 2 (1 x for choke cable, 1 x for throttle cable)

This is item number 11 in the drawing.

 

(11) Rubber Cable Boot for Dellorto PHBH and PHBL carburetors

1104
(12) Throttle Cable Adjuster for Dellorto PHBH and PHBL carburetors

(12) Throttle Cable Adjuster for Dellorto PHBH and PHBL carburetors

Throttle cable adjuster for the Dellorto PHBL and PHBH series carburetors.

Required number per carburettor: 1

This is item number 12 in the drawing.

 

 

 

(12) Throttle Cable Adjuster for Dellorto PHBH and PHBL carburetors

9372
(13) Black Plastic Top Cover for Dellorto PHBH carburetors

(13) Black Plastic Top Cover for Dellorto PHBH carburetors

Black Plastic Top Cover for Dellorto PHBH carburetors.

This is the current production, black plastic, version

Required number per carburettor: 1

This is item number 13 in the drawing.

 

 

(13) Black Plastic Top Cover for Dellorto PHBH carburetors

9375
(15) Needle Plate for Dellorto PHBH carburetors

(15) Needle Plate for Dellorto PHBH carburetors

Needle plate to locate the needle and support the slide spring inside the slide of the Dellorto PHBH carburetors.

Required quantity per carburettor: 1

This is item number 15 in the drawing.

 

 

 

(15) Needle Plate for Dellorto PHBH carburetors

9563
(15) Needle Plate for Dellorto PHBL carburetors

(15) Needle Plate for Dellorto PHBL carburetors

Needle plate to locate the needle and support the slide spring inside the slide of the Dellorto PHBL carburetors.

Required quantity per carburettor: 1

This is item number 15 in the drawing.

 

 

 

(15) Needle Plate for Dellorto PHBL carburetors

9596
(16) Needle Circlip for Dellorto PHBH and PHBL carburetors

(16) Needle Circlip for Dellorto PHBH and PHBL carburetors

Circlip to secure the needle on the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 16 in the drawing.

 

 

(16) Needle Circlip for Dellorto PHBH and PHBL carburetors

8542
(21) Top Cover Screw Bolt for Dellorto PHBH and PHBL carburetors

(21) Top Cover Screw Bolt for Dellorto PHBH and PHBL carburetors

Screw / Bolt that secures the top cover on the Dellorto PHBL and PHBL series carburetors.

Required quantity per carburettor: 2

This is item number 21 in the drawing.

 

 

 

(21) Top Cover Screw Bolt for Dellorto PHBH and PHBL carburetors

1481
(22) Cable Adjuster for Dellorto PHBH and PHBL carburetors

(22) Cable Adjuster for Dellorto PHBH and PHBL carburetors

Cable adjuster for the Dellorto PHBH and PHBL carburetors.

Fits an outer cable with an external diameter of 6.75 mm.

This cable adjuster uses Lock Nut 1692 to secure its setting.
For your convenience, you can order this lock nut right along with this adjuster by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is part of item number 22 in the drawing.

(22) Cable Adjuster for Dellorto PHBH and PHBL carburetors

1692
(22) Lock nut for Cable Adjuster on Dellorto PHBH and PHBL carburetors

(22) Lock nut for Cable Adjuster on Dellorto PHBH and PHBL carburetors

This is the locknut that secures the setting on the throttle cable for the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is part of item number 22 in the drawing.

 

(22) Lock nut for Cable Adjuster on Dellorto PHBH and PHBL carburetors

9330
(23) 40 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

(23) 40 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

40 degrees cable elbow for the Dellorto PHBH and PHBL carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 23 in the drawing.

(23) 40 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

10854
(23) 50 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

(23) 50 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

50 degrees cable elbow for the Dellorto PHBH and PHBL carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 23 in the drawing.

(23) 50 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

3600
(23) 70 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

(23) 70 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

70 degrees cable elbow for the Dellorto PHBH and PHBL carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 23 in the drawing.

(23) 70 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

3698
(23) 90 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

(23) 90 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

90 degrees cable elbow for the Dellorto PHBH and PHBL carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 23 in the drawing.

(23) 90 Degree Cable Elbow for Dellorto PHBH and PHBL carburetors

1691
Lock Nut for Cable Elbow on Dellorto carburetors

Lock Nut for Cable Elbow on Dellorto carburetors

This lock nut is used on a wide variety of Dellorto carburetors to secure the cable elbow into the top cover.

Required quantity per elbow: 1

This item is usually NOT depicted in the drawing.

 

 

 

Lock Nut for Cable Elbow on Dellorto carburetors

7745
(27) Choke Assembly Support Screw for Dellorto PHBH and PHBL carburetors

(27) Choke Assembly Support Screw for Dellorto PHBH and PHBL carburetors

Screw that secures the choke assembly to the body of the carburetor on the Dellorto PHBL and PHBH series carburetors.

Required quantity per carburettor: 1

This is item number 27 in the drawing.

 

 

 

(27) Choke Assembly Support Screw for Dellorto PHBH and PHBL carburetors

8297
(30) O Ring for Choke Assembly on Dellorto PHBH and PHBL carburetors

(30) O Ring for Choke Assembly on Dellorto PHBH and PHBL carburetors

Rubber (Viton) o-ring that seals the choke assembly to the body of the carburetor on the Dellorto PHBL and PHBH series carburetors.

Required quantity per carburettor: 1

This is item number 30 in the drawing.

 

 

 

(30) O Ring for Choke Assembly on Dellorto PHBH and PHBL carburetors

8294
(32) Lever-Operated Choke Mechanism for Dellorto PHBH and PHBL carburetors - Short

(32) Lever-Operated Choke Mechanism for Dellorto PHBH and PHBL carburetors - Short

Lever-operated choke mechanism for the Dellorto PHBH and PHBL carburetors.

Please note that the working height of this version is 34 mm.

Please make sure that this is the correct version for your carburetor.

Required quantity per carburettor: 1

This is item number 32 in the drawing.

(32) Lever-Operated Choke Mechanism for Dellorto PHBH and PHBL carburetors - Short

1104
(33) Choke Cable Adjuster for Dellorto PHBH and PHBL carburetors

(33) Choke Cable Adjuster for Dellorto PHBH and PHBL carburetors

Choke cable adjuster for the Dellorto PHBL and PHBH series carburetors.

This adjuster uses lock nut Number 1691 to secure its setting.

For your convenience, you can order this nut right along with the adjuster by selecting it through the drop box above.

Required number per carburettor: 1

This is item number 33 in the drawing.

(33) Choke Cable Adjuster for Dellorto PHBH and PHBL carburetors

1691
(33) Lock Nut for Choke Cable Adjuster on Dellorto PHBH and PHBL carburetors

(33) Lock Nut for Choke Cable Adjuster on Dellorto PHBH and PHBL carburetors

Lock nut to secure the setting on the choke cable adjuster on the Dellorto PHBL and PHBH series carburetors.

Required quantity per carburettor: 1

This is item number 33 in the drawing.

 

 

 

(33) Lock Nut for Choke Cable Adjuster on Dellorto PHBH and PHBL carburetors

8295
(34) Choke Assembly Support for Dellorto PHBH and PHBL carburetors

(34) Choke Assembly Support for Dellorto PHBH and PHBL carburetors

Choke assembly support for the Dellorto PHBL and PHBH series carburetors.

Required quantity per carburettor: 1

This is item number 34 in the drawing.

 

 

 

(34) Choke Assembly Support for Dellorto PHBH and PHBL carburetors

3133
(35) Choke Return Spring for Dellorto PHBH and PHBL carburetors

(35) Choke Return Spring for Dellorto PHBH and PHBL carburetors

Choke return spring for the Dellorto PHBL and PHBH series carburetors.

Required quantity per carburettor: 1

This is item number 35 in the drawing.

 

 

(35) Choke Return Spring for Dellorto PHBH and PHBL carburetors

3238
(36) Choke Piston for Dellorto PHBH and PHBL carburetors

(36) Choke Piston for Dellorto PHBH and PHBL carburetors

Choke piston for the Dellorto PHBL and PHBH series carburetors.

Required quantity per carburettor: 1

This is item number 36 in the drawing.

 

 

 

 

(36) Choke Piston for Dellorto PHBH and PHBL carburetors

7449
(37) Mixture screw for Dellorto PHBH and PHBL carburetors

(37) Mixture Screw for Dellorto PHBH and PHBL carburetors

Mixture screw for the Dellorto PHBH and PHBL carburetors.

Total length: 33 mm

Tip length: 2.5 mm

Parallel shaft length: 17.4 mm

Please note that this version is NOT suitable for the Cagiva Mito.

Required quantity per carburettor: 1

This is item number 37 in the drawing.

(37) Mixture screw for Dellorto PHBH and PHBL carburetors

7446
(38) Mixture Screw Spring for Dellorto PHBH and PHBL carburetors

(38) Mixture Screw Spring for Dellorto PHBH and PHBL carburetors

Mixture Screw Spring for Dellorto PHBH and PHBL carburetors.

Spring that secures the setting of the mixture screw on the PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 38 in the drawing.

 

(38) Mixture Screw Spring for Dellorto PHBH and PHBL carburetors

8260
(39) Mixture Screw Spring Washer for Dellorto PHBH and PHBL carburetors

(39) Mixture Screw Spring Washer for Dellorto PHBH and PHBL carburetors

Washer that keeps the mixture screw spring in place on the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 39 in the drawing.

 

(39) Mixture screw spring washer for Dellorto PHBH and PHBL carburetors

8678
(40) O-Ring for Mixture Screw on Dellorto PHBH and PHBL carburetors

(40) O-Ring for Mixture Screw on Dellorto PHBH and PHBL carburetors

Viton (rubber) O-Ring for mixture screw on Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 40 in the drawing.

 

 

(40) O-Ring for mixture screw on Dellorto PHBH and PHBL carburetors

7571
(40) O Ring for Dellorto PHBH carburetors for Cagiva Mito

(40) O Ring for Dellorto PHBH carburetors for Cagiva Mito

O ring for the idle screw on the Dellorto PHBH carburetors as used on the Cagiva Mito.

Required quantity per carburettor: 1

This is item number 40 in the drawing.

 

 

(40) O Ring for Dellorto PHBH carburetors for Cagiva Mito

7673
(41) Throttle Stop Screw for Dellorto PHBH and PHBL carburetors

(41) Throttle Stop Screw for Dellorto PHBH and PHBL carburetors

Throttle Stop Screw for Dellorto PHBH and PHBL carburetors.

Screw to regulate the idle opening of the throttle slide on this range of carburettors.

Total length: 29.5 mm
Please contact us by email in case that you require a different length.

Required quantity per carburettor: 1

This is item number 41 in the drawing.

(41) Throttle Stop Screw for Dellorto PHBH and PHBL carburetors

4670
(42) Throttle Stop Screw Spring for Dellorto PHBH and PHBL carburetors

(42) Throttle Stop Screw Spring for Dellorto PHBH and PHBL carburetors

Throttle stop screw spring for Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 42 in the drawing.

 

 

(42) Throttle Stop Screw Spring for Dellorto PHBH and PHBL carburetors

4650
(43) Throttle Stop Washer for Dellorto PHBH and PHBL carburetors

(43) Throttle Stop Washer for Dellorto PHBH and PHBL carburetors

Throttle Stop Washer for Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 43 in the drawing.

 

 

(43) Throttle Stop Washer for Dellorto PHBH and PHBL carburetors

7540
(44) Throttle Stop Screw O ring for Dellorto PHBH and PHBL carburetors

(44) Throttle Stop Screw O ring for Dellorto PHBH and PHBL carburetors

Viton O-ring to seal the throttle stop screw on the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 44 in the drawing.

 

(44) Throttle Stop Screw O ring for Dellorto PHBH and PHBL carburetors

6173
(47) Starter jet o-ring for Dellorto PHBH and PHBL carburetors

(47) Starter jet o-ring for Dellorto PHBH and PHBL carburetors

Starter jet o-ring for the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 47 in the drawing.

 

 

(47) Starter jet o-ring for Dellorto PHBH and PHBL carburetors

8128
(49) Nut for Manifold Clamp for Dellorto PHBL carburetors

(49) Nut for Manifold Clamp for Dellorto PHBL carburetors

Nut for Manifold Clamp for Dellorto PHBL carburetors.

Special nut to secure the bolt on the manifold clamp.

Required quantity per carburettor: 1

This is item number 49 in the drawing.

 

 

(49) Nut for Manifold Clamp for Dellorto PHBL carburetors

8127
(51) Bolt for Manifold Clamp for Dellorto PHBL carburetors

(51) Bolt for Manifold Clamp for Dellorto PHBL carburetors

Bolt for Manifold Clamp for Dellorto PHBL carburetors.

Special bolt to secure the manifold clamp.

Required quantity per carburettor: 1

This is item number 51 in the drawing.

 

 

 

(51) Bolt for Manifold Clamp for Dellorto PHBL carburetors

6109
(53) Banjo Fuel Filter for Dellorto PHBH and PHBL carburetors

(53) Banjo Fuel Filter for Dellorto PHBH and PHBL carburetors

Special fuel filter to fit the banjo fuel bolt of the Dellorto PHBL and PHBH carburetors.

Required quantity per carburettor: 1

This is item number 53 in the drawing.

 

(53) Banjo Fuel Filter for Dellorto PHBH and PHBL carburetors

6273
(54) 8 mm Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

(54) 8 mm Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

Metal fuel inlet banjo for the Dellorto PHBH and PHBL carburetors.

Please note that there are three version of this inlet banjo: a single plastic one, a double metal one and this single metal version.

For your convenience, you can order this inlet banjo complete with new fiber washer and new banjo bolt or without it.

Required quantity per carburettor: 1

This is item number 54 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(54) 8 mm Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

6517
(54) Angled Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

(54) Angled Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

Metal fuel inlet banjo for the Dellorto PHBH and PHBL carburetors.

Please note that there are three version of this inlet banjo: a single plastic one, a double metal one and this single metal version.

This is the metal version with the fuel union under an angle of approximately 45 degrees (see photos).

For your convenience, you can order this inlet banjo complete with new fiber washer and new banjo bolt or without it.

Required quantity per carburettor: 1

This is item number 54 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(54) Angled Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

4052
(55) Banjo Bolt Fibre Washer for Dellorto PHBH and PHBL carburetors

(55) Banjo Bolt Fibre Washer for Dellorto PHBH and PHBL carburetors

Banjo bolt fibre washer for the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 55 in the drawing.

 

 

(55) Banjo Bolt Fibre Washer for Dellorto PHBH and PHBL carburetors

4568
(56) Long Fuel Banjo Bolt for Dellorto PHBH and PHBL carburetors

(56) Long Fuel Banjo Bolt for Dellorto PHBH and PHBL carburetors

Fuel banjo bolt for the Dellorto PHBH and PHBL carburetors with 8 mm pipe fitting banjos only.

This bolt has an overall length of some 21 mm with a shaft length of approximately 17.5 mm and will NOT fit the banjos for 6 mm fuel lines.

Required quantity per carburettor: 1

This is item number 56 in the drawing.

(56) Long Fuel Banjo Bolt for Dellorto PHBH and PHBL carburetors

8752
(57) 6 mm Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

(57) 6 mm Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

This is the single metal fuel inlet banjo for the Dellorto PHBH and PHBL series carburetors with 6 mm fuel union.

This banjo uses the short banjo bolt.

Required quantity per carburettor: 1

This is item number 57 in the drawing.

This banjo uses fuel line with an internal diameter of 6 mm.

(57) 6 mm Metal Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

4053
(58) Short Fuel Banjo Bolt for Dellorto PHBH and PHBL carburetors

(58) Short Fuel Banjo Bolt for Dellorto PHBH and PHBL carburetors

Fuel banjo bolt for the Dellorto PHBH and PHBL carburetors with 6 mm pipe fitting banjos only.

This bolt has an overall length of some 18 mm with a shaft length of approximately 14 mm.

Required quantity per carburettor: 1

This is item number 58 in the drawing.

(58) Short Fuel Banjo Bolt for Dellorto PHBH and PHBL carburetors

9250
(59) Plastic Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

(59) Plastic Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

Plastic fuel inlet banjo for the Dellorto PHBH and PHBL carburetors.

Please note that there are three version of this inlet banjo: a single metal one, a double metal one and this single plastic version.

This plastic version does NOT use a fiber ring, contrary to the metal versions.

For your convenience, you can order this inlet banjo complete with a new banjo bolt or without it.

Required quantity per carburettor: 1

This is item number 59 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(59) Plastic Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

7890
(60) 8 mm Double Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

(60) 8 mm Double Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

This is the, TWIN, metal fuel inlet banjo for the Dellorto PHBL and PHBH carburetors for 8 m fuel lines.

Please note that there is also a SINGLE metal version and a SINGLE plastic version in various connection sizes.

This double metal version which uses fiber washer number 4052.

This double metal version which uses banjo bolt 4568.

For your convenience, you can order this inlet banjo complete with fiber washer and banjo bolt or simply without these extras.

Required quantity per carburettor: 1

This is item number 60 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(60) 8 mm Double Fuel Inlet Banjo for Dellorto PHBH and PHBL carburetors

6288
(61) Fiber Ring for the Needle Valve on the Dellorto PHBL and PHBH carburetors

(61) Fiber Ring for the Needle Valve on the Dellorto PHBL and PHBH carburetors

Fiber ring to seal the needle valve on the Dellorto PHBL and PHBH carburetors.

Required quantity per carburettor: 1

This is item number 61 in the drawing.

 

 

 

(61) Fiber Ring for the Needle Valve on the Dellorto PHBL and PHBH carburetors

7346
(64) Float Pivot Pin for Dellorto PHBH and PHBL carburetors

(64) Float Pivot Pin for Dellorto PHBH and PHBL carburetors

Standard float pivot pin for the Dellorto PHBH and PHBL carburetors.

Required quantity per carburettor: 1

This is item number 64 in the drawing.

 

 

 

(64) Float Pivot Pin for Dellorto PHBH and PHBL carburetors

15760
(72) Single white plastic float for Dellorto PHBH and PHBL carburetors

(72) Single white plastic float for Dellorto PHBH and PHBL carburetors

Single, white plastic, float for the Dellorto PHBH and PHBL carburetors.

Available in the following versions:

  • 15760.3 - 4.0 grams
  • 15760.4 - 5.2 grams
  • 15760.5 - 3.6 grams

Required quantity per carburettor: 2

This is item number 72 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHBH and PHBL.

(72) Single white plastic float for Dellorto PHBH and PHBL carburetors

9794
(72) Single black plastic float for Dellorto PHBH and PHBL carburetors

(72) Single black plastic float for Dellorto PHBH and PHBL carburetors

Single, black plastic, float for the Dellorto PHBH and PHBL carburetors.

Available in the following versions:

  • 9794.1 - 3.5 gram
  • 9794.3 - 3.5 gram
  • 9794.4 - 4.5 gram
  • 9794.5 - 2.8 gram

Required quantity per carburettor: 2

This is item number 72 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHBH and PHBL.

(72) Single black plastic float for Dellorto PHBH and PHBL carburetors

9543
(73) 55 mm trumpet for Dellorto PHBH carburetors

(73) 55 mm trumpet for Dellorto PHBH carburetors

55 millimeter long trumpet for the Dellorto PHBH carburetors.

Grey plastic.

42 mm threaded connection.

Required quantity per carburettor: 1

This is item number 73 in the drawing.

(73) 55 mm trumpet for Dellorto PHBH carburetors

MCT09
(73) Aluminum 30 mm trumpet for Dellorto PHBH carburetors

(73) Aluminum 30 mm trumpet for Dellorto PHBH carburetors

Aluminum 60 mm trumpet for Dellorto PHBH carburetors.

Milled from a solid piece of aluminum with a crimped-on gauze.

M42 x 1.25 threaded connection.

The gauze adds some 15 mm to the length of the trumpet bringing the overall length to some 75 mm.

The diameter at the gauze end is some 75 mm.

Required quantity per carburettor: 1

This is item number 73 in the drawing.

(73) Aluminum 30 mm trumpet for Dellorto PHBH carburetors

MCT10
(73) Aluminum 60 mm trumpet for Dellorto PHBH carburetors

(73) Aluminum 60 mm trumpet for Dellorto PHBH carburetors

Aluminum 60 mm trumpet for Dellorto PHBH carburetors.

Milled from a solid piece of aluminum with a crimped-on gauze.

M42 x 1.25 threaded connection.

The gauze adds some 15 mm to the length of the trumpet bringing the overall length to some 45 mm.

The diameter at the gauze end is some 75 mm.

Please note that in some pictures, the trumpet is depicted on a carburetor.
This carburetor is NOT included in the price.

Required quantity per carburettor: 1

This is item number 73 in the drawing.

(73) Aluminum 60 mm trumpet for Dellorto PHBH carburetors

52523
(74) Service Kit for Dellorto PHBH carburetors

(74) Service Kit for Dellorto PHBH carburetors

Dellorto factory-original service kit for the Dellorto PHBH carburetors.

Contains all required fiber rings, gaskets and cable boot.

Required quantity per carburetor: 1

This is item number 74 in the drawing.

 

 

(74) Service Kit for Dellorto PHBH carburetors

52581
(74) Service Kit for Dellorto PHBH FS and FD carburetors

(74) Service Kit for Dellorto PHBH FS and FD carburetors

Dellorto factory-original service kit for the FS and FD versions of the Dellorto PHBH carburetors.

Contains all required fiber rings, gaskets etc. to service 1 carburetor.

Required quantity per carburetor: 1

This is item number 74 in the drawing.

 

 

(74) Service Kit for Dellorto PHBH FS and FD carburetors

52524
(74) Service Kit for Dellorto PHBL carburetors

(74) Service Kit for Dellorto PHBL carburetors

Dellorto factory-original service kit for the Dellorto PHBL carburetors.

Contains all required fiber rings, gaskets and cable boot.

Required quantity per carburetor: 1

This is item number 74 in the drawing.

 

 

(74) Service Kit for Dellorto PHBL carburetors

11600
(75) Power Jet for Dellorto PHBH carburetors

(75) Power Jet for Dellorto PHBH carburetors

Power Jet for certain versions of Dellorto PHBH carburetors.

Please note that NOT all versions of the PHBH were equipped with this Power Jet.

Where possible, we only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo. However, sizes that are no longer supplied by Dellorto themselves are manufactured for us at the exact same high standards.

Thread size: M4
Head diameter: 5mm
Thread length: 4mm
Total length: 7mm

In stock in sizes:

  • 40
  • 45
  • 60

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 75 in the drawing.

(75) Power Jet for Dellorto PHBH carburetors

7453
(82) Manifold Sleeve for Dellorto PHBH carburetors

(82) Manifold Sleeve for Dellorto PHBH carburetors

Manifold Sleeve for Dellorto PHBH carburetors.

This sleeve has the following dimensions:

  • Internal diameter 35 mm
  • External diameter 40 mm
  • External depth 22 mm
  • Internal depth to lip 20 mm

Required quantity per carburettor: maximum 1, depending on set-up

This is item number 82 in the drawing.

(82) Manifold Sleeve for Dellorto PHBH carburetors

9008
Breather Pipe Connection for Dellorto PHBH and PHBL carburetors

Breather Pipe Connection for Dellorto PHBH and PHBL carburetors

This breather pipe connector will fit a wide range of Dellorto carburetors, amongst which the PHBH and PHBL series carburettors.

This pipe has 5 mm push fit in the carburettor body and connects to a 3.8 mm internal diameter breather line.

Required quantity per carburettor: 1

This item is NOT shown in the drawing.

Breather Pipe Connection for Dellorto PHBH and PHBL carburetors

MC004
RamAir MR004 43 mm Pod Airfilter with Chrome Cover for Dellorto PHBH carburators

RamAir MR004 43 mm Pod Airfilter with Chrome Cover for Dellorto PHBH carburators

RamAir MR004 Airfilter with Chrome Cover for Dellorto PHBH carburators.

Ramair 43mm pod filter with a chrome rear cover for Dellorto PHBHs and other carburettors with 42 / 43mm air intake connections

Dimensions:

  • Fitting neck diameter (inside) 43 mm
  • Filter outer diameter 73 mm
  • Filter height (including neck) 75 mm

RamAir MR004 43 mm Pod Airfilter with Chrome Cover for Dellorto PHBH carburators

MR004
RamAir MR004 43 mm Pod Airfilter for Dellorto PHBH carburators

RamAir MR004 43 mm Pod Airfilter for Dellorto PHBH carburators

RamAir MR004 Airfilter for Dellorto PHBH carburators.

Ramair 43mm pod filter for Dellorto PHBHs and other carburettors with 42 / 43mm air intake connections

Dimensions:

  • Fitting neck diameter (inside) 43 mm
  • Filter outer diameter 73 mm
  • Filter height (including neck) 75 mm

Please note that in the photos, this filter is shown assembled on a Dellorto PHBH carburetor.
This carburetor is NOT included in the price.

RamAir MR004 43 mm Pod Airfilter for Dellorto PHBH carburators

C1050
C1050 Pipercross Universal Airfilter Socks for Ram Pipes

C1050 Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

These socks are easily tailored to size by shortening them with a pair of scissors.

The generous inner diameter makes them suitable for virtually all rampipes.

Created out of the famous Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

This is the "normal" version, very well suited for street and track use. Should you be using your vehicle in extremely dusty circumstances, like auto- and motocross, we recommend the Heavy Duty version, C1050MX.

Dimensions:

  • Internal diameter: 70 mm
  • External diameter: 95 mm
  • Internal height: 100 mm
  • External height: 115 mm

Before putting the socks in place, you cut them to size. Then slide them onto the ram pipes and, when desired, you can secure them in place with a simple plastic tie-strap.

Although Pipercross supplies these only in pairs, we understand the need in the market for "singles" and consequently we sell these individually.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1050 Pipercross Universal Airfilter Socks for Ram Pipes

C1050MX
C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous Heavy Duty Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

These socks are easily tailored to size by shortening them with a pair of scissors.

The generous inner diameter makes them suitable for virtually all rampipes.

Created out of not less than 3 layers of the famous, green, Heavy Duty Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

Being the heavy duty version, these socks are very well suited for use in extremely dusty circumstances like auto- and motocross.

For street and track use, the better option is to pick the normal version, C1050.

Dimensions:

  • Internal diameter: 55 mm
  • External diameter: 95 mm
  • Internal height: 95 mm
  • External height: 120 mm

Before putting the socks in place, you cut them to size. Then slide them onto the ram pipes and, when desired, you can secure them in place with a simple plastic tie-strap.

Although Pipercross supplies these only in pairs, we understand the need in the market for "singles" and consequently we sell these individually.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

C1052
C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous "enclosed" Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

Contrary to the C1050 "open" socks, this version has a rear panel with opening so that it "hugs" the ram pipe.

The generous inner diameter makes them suitable for virtually all rampipes.

The opening in the rear panel measures some 55 mm in diameter but can of course be stretched significantly thanks to the nature of the foam.

Created out of 3 layers of the the famous Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

Dimensions:

  • Internal diameter: 80 mm
  • External diameter: 110 mm
  • Internal height: 42.5 mm
  • External height: 70 mm

Simply slide the sock onto the ram pipes and, when desired, you can secure them in place with a plastic tie-strap.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

PRO804
Sytec Pro-Line in-line fuel filter - 6 mm

Sytec Pro-Line in-line fuel filter - 6 mm

In line fuel filter with cleanable / replaceable filter.

Suitable for 6 mm internal diameter fuel hoses.

Replacement filter elements are available HERE.

Chrome finish.

Toughened glass phial.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

Supplied with 2 Jubilee clips.

Couplings Specifications:
Fuel Unions for fuel lines with 6 mm internal diameter

Sytec Pro-Line in-line fuel filter - 6 mm

PRO805
Sytec Pro-Line in-line fuel filter - 8 mm

Sytec Pro-Line in-line fuel filter - 8 mm

In line fuel filter with cleanable / replaceable filter.

Suitable for 8 mm internal diameter fuel hoses.

Replacement filter elements are available HERE.

Chrome finish.

Toughened glass phial.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

Supplied with 2 Jubilee clips.

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Sytec Pro-Line in-line fuel filter - 8 mm

PRO896
Replacement elements for Sytec in-line fuel filter

Replacement elements for Sytec in-line fuel filter

3 replacement elements for the Sytec Pro-Line in-line fuel filter.

Come complete with new rubber seals.

These elements fit our PRO804 and PRO805 Sytec in-line fuel filters.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

 

 

 

 

Replacement elements for Sytec in-line fuel filter

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15 MM
  • 0.25 MM
  • 0.4 MM
  • 0.8 MM
  • 1.6 MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

gatestextiel6mm
Gates textile covered fuel line hose with 6 mm inner diameter

Gates textile covered fuel line hose with 6 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 6 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 0.5 meter.

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on fuel systems in passenger cars.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 10 - 12 mm jubilee clips.

Gates textile covered fuel line hose with 6 mm inner diameter

GREENFUEL8MM-50cm
Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

Alternatively, this hose simply looks great when used with the "Endless band & Buckle" hose clamps like in the photo.

Please note:
This hose is NOT E10 resistant.
Do not use this hose if you are not able to avoid using Ethanol-containing fuels.

Italian style clear green fuel line hose with 8 mm inner diameter

gatestextiel8mm
Gates textile covered fuel line hose with 8 mm inner diameter

Gates textile covered fuel line hose with 8 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 0.5 meter.

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

Gates textile covered fuel line hose with 8 mm inner diameter

jubilee11-13
11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

DD0906
Dellorto Carburatori Sticker - Large

Dellorto Carburatori Sticker - Large

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 9 x 3 cm (3.54 x 1.2 inches).

This is Number 1 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Large

DD0909
Dellorto Carburatori Sticker - Medium

Dellorto Carburatori Sticker - Medium

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 8 x 4 cm (3.1 x 1.55 inches).

This is Number 2 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Medium

DD0905
Dellorto Carburatori Sticker - Small - Low

Dellorto Carburatori Sticker - Small - Low

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 6 x 2 cm (2.4 x 0.8 inches).

This is Number 3 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Small - Low

Patch
Dellorto Carburatori Sew-On Patch

Dellorto Carburatori Sew-On Patch

Official issue sew-on patch with the Dellorto logo and Italian flag "tricolore" colors.

Measures 12 x 6.5 cm (4.7 x 2.6 inches).

Elaborately embroidered.

 

 

Dellorto Carburatori Sew-On Patch

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker

G4125
Gunson Digital Exhaust Gas and CO Tester - G4125

Gunson Digital Exhaust Gas and CO Tester - G4125

The Gunson Digital Exhaust Gas and CO Tester is the perfect (and affordable !) tool for the DIY mechanic to measure and adjust the CO-percentage in the exhaust gases of cars, motorcycles, boats etc equipped with a petrol-driven internal combustion engines.

Allows you to measure the current CO-percentage after which you can adjust it to the required level.

This system is equipped with a pulse pump and is suitable for both leaded and unleaded petrol / gasoline.

The tester will calibrate itself in the open air, has no moving parts to reduce wear and tear and has no filters.

Measures the CO % to 0,5 % accurately throughout the range.

Power: 12 Volt car- or motorcycle battery.

The set comprises the following:

  • The Gastester with box
  • Puls pump with water trap
  • Metal exhaust probe
  • 3 Flexibel pipes
  • Operating Manual in English

If you require the owner's manual again, you can download it HERE.

Additional instructions on adjusting the Gastester, in English, can be downloaded HERE.

This is a short instruction video, again in English:

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Digital Exhaust Gas and CO Tester - G4125