Austin Allegro Carburetter Service Kits
Austin Allegro Carburetter Service Kits

Austin Allegro

Austin Allegro Carburetter Service Kits.

On this page you will find the service kits for the Allegro-series that we can supply.

If the service kit that you're looking for isn't listed yet, please contact us by email as there is a good chance that we can help you anyway.

Austin Allegro Carburetter Service Kits

!
CSK 59
CSK59 SU Carburetter Service Kit for 2 x HS2 carburetors for Austin Allegro 1300 GT

CSK59 SU Carburetter Service Kit for 2 x HS2 carburetors for Austin Allegro 1300 GT

Factory-Original Service Kit for the 1½ inch SU HS2 carburetors as fitted to, amongst others, the:

  • 1971 - 1972 Austin Allegro 1300 GT
    1275 cc
    Tags: AUD496L and AUD496R

This set contains all required parts to service 2 carburetters.

Consists, amongst others, of the following parts:

  • Various versions of airfilter gaskets
  • Various versions of inlet manifold gaskets
  • 2 Needle & Seat sets
  • 2 Float Spindles
  • Various O-Rings
  • 2 Jet Springs
  • 2 Float Lid Gaskets
  • 2 Tab Washers
  • 1 x R.H. Jet Assembly .090 inch - Identifying Sleeve Color: Green
  • 1 x L.H. Jet Assembly .090 inch - Identifying Sleeve Color: Pink
  • Damper Cap Washer

Please note that for SU, we are sticking to the nomenclature that SU themselves also use. Hence, this is officially called a "Service Kit".

For the less elaborate Gasket Kits and more elaborate Rebuild Kits, please contact us by email, we will gladly help you.

CSK59 SU Carburetter Service Kit for 2 x HS2 carburetors for Austin Allegro 1300 GT

SYNCHRONOMETER
Synchrometer airflow meter for carburetors

Synchrometer airflow meter for carburetors

Synchrometer airflow meter for various carburetors.

Pushes into the trumpet / ram pipe / velocity stack or throat to measure the airflow to enable you to balance multiple carburettors.

  • Instructions included
  • The original genuine high quality German made product
  • Can be used for all Weber DCOE and IDF and Dellorto DHLA, DRLA carbs with round intakes or trumpets
  • Can also be used with motorcycle carburetors with round intakes

    Total length of unit 121mm

    Rubber cone dimensions:
    Small end diameter 40mm
    Large end diameter 55mm
    Length of cone 36mm

Synchrometer airflow meter for carburetors

SYNCHRONOMETERSU
Synchrometer adaptor for SU carburettors

Synchrometer adaptor for SU carburettors

Synchrometer adapter to suit SU and Stromberg carburettors.

Cone dimensions: 30mm - 40mm.

Internal diameter of the hole through the middle: 25mm.

 

 

 

Synchrometer adaptor for SU carburettors

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15 MM
  • 0.25 MM
  • 0.4 MM
  • 0.8 MM
  • 1.6 MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm - SOLD OUT AT THE MOMENT!

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

Available from our Stock

G4053
Gunson Carbalancer Carburetor Synchronizing Tool

Gunson Carbalancer Carburetor Synchronizing Tool

Gunson Car Balancer.

Internal combustion engines use a mixture of air and petrol to generate their power.

The performance therefore is influenced by the air flowing into it and the petrol that is metered out by the carburettor.

Unless the air flow in Twin or Multiple carburettors is correctly set, the correct mixture adjustment is unlikely to be achieved and this is the simplest tool to achieve that.

Suitable for use on SU, Solex, Auto-Lite (Fomoco), Stromberg, Weber and Zenith and can be adjusted to fit most carburettors including sidedraft, downdraft with air intakes (Venturi) from 25 mm to 67 mm (1”-2”) diameter

  • Easy read scale indicates the air flow and allows adjustment to optimum efficiency
  • Provides smoother and better acceleration
  • Carbalancer can be adjusted to fit most carburettors
  • Easy to follow instructions

The user manual for the Gunson Carbalancer, in English, can be downloaded HERE.

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Carbalancer Carburetor Synchronizing Tool

MANOMETER2
2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easily read scale
  • Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

2 Column Manometer - Synchrometer Carbtune Pro

MANOMETER4
4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easy to read scale
  • Comes complete with 4 x 5 mm and 4 x 6 mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

4 Column Manometer - Synchrometer Carbtune Pro

9679
Brass vacuum take-off adapter for carburetors and manifolds

Brass vacuum take-off adapter for carburetors and manifolds

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Also fits the Weber DCOE series carburettors and Solex ADDHE.

 

Brass vacuum take-off adapter for carburetors and manifolds

2134.0400
Cohline E10-resistant fuel line hose with 6 mm inner diameter

Cohline E10-resistant fuel line hose with 6 mm inner diameter

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose.

This fuel hose has an 6 mm inner diameter and 12 mm outer diameter and is therewith a nice, tight, fit onto 6 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 50 mm

This hose uses 10 - 12 mm jubilee clips.

Cohline E10-resistant fuel line hose with 6 mm inner diameter

2134.01.0400
Cohline E10-resistant fuel line hose with 6 mm inner diameter and steel braiding

Cohline E10-resistant fuel line hose with 6 mm inner diameter and steel braiding

This is the top-of-the-line Cohline, steel-braided E10-resistant, flexible fuel line / hose.

This fuel hose has an 6 mm inner diameter and 13.5 mm outer diameter and is therewith suitable for 6 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 50 mm

This hose uses 12 - 14 mm jubilee clips.

Cohline E10-resistant fuel line hose with 6 mm inner diameter and steel braiding

jubilee10-12
10 - 12 mm Stainless Steel Jubilee Clip Hose Clamp

10 - 12 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 6 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 6 mm internal diameter fuel line as well as our green "Italian Style" transparent fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 10 and 12 mm internal diameter (i.e. 10 - 12 mm external hose/line diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

10 - 12 mm Stainless Steel Jubilee Clip Hose Clamp

jubilee12-14
12 - 14 mm Stainless Steel Jubilee Clip Hose Clamp

12 - 14 mm Stainless Steel Jubilee Clip Hose Clamp

12 - 14 mm Stainless Steel Jubilee Clip Hose Clamp.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to a well-cared for "under the hood" look.

It is rated for between 12 and 14 mm external diameter flexible hose / line.

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

12 - 14 mm Stainless Steel Jubilee Clip Hose Clamp

gatestextiel6mm
Gates textile covered fuel line hose with 6 mm inner diameter

Gates textile covered fuel line hose with 6 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 6 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on fuel systems in passenger cars.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 10 - 12 mm jubilee clips.

Gates textile covered fuel line hose with 6 mm inner diameter