Huco Fuel Pumps
Huco Fuel Pumps

Huco Fuel Pumps

On this page you will find our offerings on Hüco fuel pumps.

Huco was recently acquired by Hitachi and produces high quality low-pressure fuel pumps.

Huco Fuel Pumps

!
HUCOPUMPFP02
Huco Low-Pressure 12 Volt Fuel Pump Kit - Suction Type

Huco Low-Pressure 12 Volt Fuel Pump Kit - Suction Type

Huco Low-Pressure 12 Volt Fuel Pump Kit.

Hüco fuel pump for engines of up to some 160 BHP.

This is a "suction type" pump, intended to placed in the engine compartment of your vehicle.

Please see HUCOPUMPFP03 in case you require a "pressure type" pump to be placed near the fuel tank of your vehicle.

Pump specification:

  • Flow rate 27.5 Gallons/hour / 125 liters/hour
  • Pressure: 2.1 PSI / 0.15 Bar
  • 12 - 14 Volt - negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol or Bio-Diesel

Kit includes:

  • Pump
  • Mounting bracket

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Thanks to its operating pressure of 2.1 PSI (some 0.15 Bar), this Huco pump does not require a pressure regulator which makes it a very cost-efficient proposition.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Huco Low-Pressure 12 Volt Fuel Pump Kit - Suction Type

HUCOPUMPFP03
Huco Low-Pressure 12 Volt Fuel Pump Kit - Pressure Type

Huco Low-Pressure 12 Volt Fuel Pump Kit - Pressure Type

Huco Low-Pressure 12 Volt Fuel Pump Kit.

Hüco fuel pump for engines of up to some 160 BHP.

This is a "pressure type" pump, intended to placed near the fuel tank.

Please see HUCOPUMPFP02 in case that you require a "suction type" pump to be placed in the engine compartment of your vehicle.

Pump specification:

  • Flow rate 27.5 Gallons/hour / 125 liters/hour
  • Pressure: 2.1 PSI / 0.15 Bar
  • 12 - 14 Volt - negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol or Bio-Diesel

Kit includes:

  • Pump
  • Mounting bracket

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Thanks to its operating pressure of 2.1 PSI (some 0.15 Bar), this Huco pump does not require a pressure regulator which makes it a very cost-efficient proposition.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Huco Low-Pressure 12 Volt Fuel Pump Kit - Pressure Type

WFP150KIT
Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Newly arrived Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Webcon In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on low-pressure fuel systems for carburetors.

A high-pressure set for fuel injection systems can be found HERE.

Spare, brass, blanking plugs can be found HERE.

We advise Loctite 543 Thread Sealant to secure the gauge in the adapter.

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

WFP151KIT
Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Newly arrived Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Webcon In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on high-pressure injection systems.

A low-pressure set for carbureted systems can be found HERE.

Spare, brass, blanking plugs can be found HERE.

We advise Loctite 543 Thread Sealant to secure the gauge in the adapter.

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

FPP01
Fuel Union for Huco Low-Pressure Fuel Pump

Fuel Union for Huco Low-Pressure Fuel Pump

Fuel Union for Huco Low-Pressure Fuel Pump.

Fits both varieties of the Hüco pump that we carry in our range.

Is supplied complete with O-Ring.

Suitable for fuel lines with 8 mm internal diameter.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

 

Fuel Union for Huco Low-Pressure Fuel Pump

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker