Holley Fuel Pumps
Holley Fuel Pumps

Holley Fuel Pumps

Holley Fuel Pumps.

On this page you will find our offerings on Holley fuel pumps.

Holley fuel pumps are renowned for their quality, high flow rate and logevity thanks to their "vanes" design as opposed to most other pumps which are either piston pumps or solid state.

Holley Fuel Pumps

!
HOLLEY128021KIT
Holley 12 Volt Vanes-Type Fuel Pump Kit with Pressure Regulator

Holley 12 Volt Vanes-Type Fuel Pump Kit with Pressure Regulator

Holley 12 Volt Vanes-Type Fuel Pump Kit with Pressure Regulator.

This is the famous Holley Blue Label Vanes Fuel pump.

It is the perfect alternative to the more usual plunger / piston and Solid-State pumps.

Thanks to its vanes-design, there is virtually no pulsation and less wear and tear.

It comes complete with suitable pressure regulator, capable of handling pressures up to 14 PSI.

Pump specification:

  • Current draw: 3 Amps
  • Voltage: 12 Volts
  • Flow rate (free): 110 Gallons / 400 Liters per hour
  • Flow rate at 9 PSI (0.6 Bar): 88 Gallons / 330 Liters per hour
  • Maximum Pressure: 14 PSI / 0.95 Bar
  • Includes an externally accessible pressure regulator
  • Weight: 3 Lbs / 1.36 KG
  • Inlet- and Outlet-Size: 3/8" NPT

Suitable for many different fuels, including modern ones, but NOT suited for Methanol or Ethanol based fuels.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

As specified above, this pump uses 3/8th NPT thread for its couplings.

This thread is not widely available in all corners of the earth.
For this reason we offer suitable fuel unions HERE.

In total you need 5 unions (2 on the pump and 3 on the regulator).

To make life even easier for you, you can order 8 mm straight fuel unions right along with your pump by selecting them through the drop-box above.

When ordered separately, these 5 unions would cost US$ 29.75.
When ordered along with the pump, we can discount them to US$ 25.00 for the set of 5.

Holley 12 Volt Vanes-Type Fuel Pump Kit with Pressure Regulator

38NPT8MM
8 mm Pipe Union with 3/8 NPT thread

8 mm Pipe Union with 3/8 NPT thread

Brass straight 8 mm Pipe Union with 3/8th thread.

Union with 3/8" NPT thread for fuel lines with an internal diameter of 8 mm.

Specification:
Inlet: 3/8" NPT
Outlet: 8 millimeter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 542 Thread Sealant which will offer the added properties of protecting your connections from undoing themselves.

Despite the barbed edge on these unions, we strongly advise you to secure your fuel lines using our Premium Quality Stainless Steel Jubilee Clips.
For your convenience, you can order these right along with the joiner by simply selecting them through the dropbox.

8 mm Pipe Union with 3/8 NPT thread

WFP150KIT
Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

Webcon In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on low-pressure fuel systems for carburetors.

A high-pressure set for fuel injection systems can be found HERE.

Spare, brass, blanking plugs can be found HERE.

We advise Loctite 543 Thread Sealant to secure the gauge in the adapter.

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 15 PSI / 0 - 1 Bar

WFP151KIT
Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

Webcon In-Line Fuel Pressure Gauge Kit.

A fantastically finished set to build your own in-line fuel pressure monitoring system.

Specifically for, low-pressure carburetor systems.
NOT suited for high-pressure fuel-injection systems!

The set consists of:

Suitable for flexible fuel lines with an internal diameter of 8 mm.

The adapter is machined from a solid billet of aluminum.

This set is intended to be used on high-pressure injection systems.

A low-pressure set for carbureted systems can be found HERE.

Spare, brass, blanking plugs can be found HERE.

We advise Loctite 543 Thread Sealant to secure the gauge in the adapter.

Webcon In-Line Fuel Pressure Gauge Kit - 0 - 120 PSI / 0 - 8 Bar

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant