Newly arrived Carburetor Parts and Service Kits
Mikuni Main Jet - Large Round Type.
For the physical dimensions, please see the photograph (sizes indicated in millimeters).
These jets are available from our stock in the following sizes:
Other sizes are available at request.
Please note that the variety of Mikuni jets is really overwhelming and that it is very well possible that your carburetor uses a different type of jet.
For this reason, we have created the Mikuni Motorcycle Jets page.Please visit this page to find the Mikuni jet that you're looking for.
These are Carburetor City jets of outstanding Japanese manufacture.
Mikuni Main Jet - Large Round Type
Seal for the needle valve for the 3-barrel versions of the following models of Weber carburetors:
Required quantity per carburettor: 2
This is item number 75 in the drawing.
Weber Part Number: 83002.125
(75) Needle Valve Seal for Weber 3-Barrel carburetors - IDA - IDAP - IDL - IDPT - IDS - IDT - IF - 83002.125
This is a complete overhaul kit for the Fispa Fuel Pressure Regulator.
Please note that Fispa has produced at least two different versions over the years:
The difference between the two will be clear from this picture:
There are more differences than just the pin but the pin is the best indicator for which kit you need.
The set with the diaphragm WITHOUT pin can be found HERE.
Officially, this set suits both the Fispa FB43 and FRB11 fuel filters with build-in pressure regulator.
The bolt pattern is as follows: circa 33 mm heart-to-heart and about 42 mm across (diagonally).
This set is E10- and bio-fuel resistant.
Rebuild kit for Fispa Fuel Pressure Regulator Kit WITH Pin
Service Kit for the Keihin carburetors as used on the 1977 and 1978 Honda CB750F F2 motorcycles.
This service kit contains the following parts to service 1 carburettor:
Although these carburetors were originally delivered on the above mentioned Honda CB750F F2, they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.
Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.
This is a Carburetor City service kit of outstanding Japanese manufacture.
Service kit for Keihin Carburetors on Honda CB750F F2 1977-1978
This is a set of 2, cast, bent rampipes for 40 mm carburetors.
These trumpets became world-famous when they were used on Alfa Romeo's GTA racing cars.
By means of the special braces (included!) the trumpets can swivel a full 360 degrees and consequently can be adjusted exactly to your personal needs.
As visible in the pictures, the trumpets are thick-walled, cast, aluminium with a crimped-on coarse mesh gauze.
When desired, the Pipercross "socks" can be used for extra filtration.You can find our Pipercross selection HERE.
This particular set consists of 2 rampipes and 2 brackets.
The sets are available for 40 mm diameter carburetors and, at a small premium, also for 45 mm.
The outside diameters are as follows:
Total "depth" per rampipe: 12 cm + 0.4 cm for the mounting plateDiameter at the flared end is some 72 mm including the crimp-ring for the gauzeAdded length for the gauze: 27 mm
These trumpets will fit most twin barrel carburetors like:
Set of 2 Curved Rampipes - GTA-Style
This is a set of 4, cast, bent rampipes for 40 mm carburetors.
These sets became world-famous when they were used on Alfa Romeo's GTA racing cars.
Tailor-made for Alfa-Romeo Nord engines, these comes complete with a top quality machined aluminum mounting plate to provide a solid base to secure the two carburetors and maintain the balance between the two.
This particular set consists of 4 rampipes, 4 brackets and a mounting plate.
These sets will fit Alfa Romeo Nord engines equipped with the following carburetors:
Set of 4 Curved Rampipes - Alfa Romeo GTA-Style
Pump diaphragm for the Weber 40DCN21 series carburetors.
Please noe that not all versions of the Weber DCN have a pump.
Required quantity per carburettor: 1
This is item number 18 in the drawing.
Weber Part number: 47407.249, replaces the obsolete number 47407.018 which is no longer available.
(18) Pump Diaphragm for Weber 40 DCN 21 carburetors - 47407.249
Air Corrector Jet for the Weber 3- Barrel carburetors.
Available from our stock in size:
Other sizes are available on request.
Fits the 3-barrel versions of the following models:
Apart from the above mentioned carburettors, these jets are used in a multitude of other Weber carburetors so please contact us if your carburetor model isn't listed on our website yet.
This is item number 74 in the drawing.
Weber Part Number: 77201
(74) Air Corrector for Weber 3-Barrel Carburetors - IDA - IDAP - IDL - IDPT - IDS - IDT - IF - 77201
Stainless Steel Push-fit Mesh Trumpet Gauzes for our 45 mm diameter trumpets.
These trumpet gauzes / covers are ideal for installations with very little clearance and room.
With the outer ring being made of rubber, they can be easily removed and re-fitted for shows etc.
These have a soft outer ring that is a push fit over 62 to 65 mm diameter trumpets.
The gauze is made up of 2 layers of stainless steel wire with a fine mesh filter sandwiched between them.
They will fit:
The price is for 1 trumpet gauze & retaining ring (Carburettor not included).
The gauze dome is approximately 30 mm high.
The version for 40 mm carburetors can be found HERE.
Stainless Steel Push-fit Mesh Trumpet Gauzes for 45 mm Trumpets
Air corrector jet for the Zenith TIN 40 carburetors as used, amongst others, on the Porsche 911.
Available from stock in sizes:
Other sizes might be available on request.Please contact us through our Contact Page for this.
Required quantity per carburetor: 3
This is Number 4 in the drawing.
(4) Air Corrector Jet for Zenith 40 TIN Carburetors
Diaphragm for Aisan carburetors.
Sometimes, an extra diaphragm was used on the various Aisan carburetors, which were produced for various automakers such as Daihatsu, Innocenti and Toyota.
We are now able to supply two of these diaphragms.
As you can see from the photograph, the difference is in the shaft, or lack thereof.
We are also showing such a diaphragm "in-place" on an Aisan carburetor.
The way it is mounted on the carb, makes it hard to determine which of the two you would require.
Consequently, it is required that you partially disassemble the mechanism to determine which one you need.
These Carburetor City diaphragms are of outstanding Italian manufacture.
Diaphragm for Aisan carburetors for Daihatsu - Innocenti - Toyota
Service kit for the Weber 28/32 TLDM series carburetors.
Contains, amongst others, the following parts to service 1 carburettor:
Service kit for Weber 28/32 TLDM carburetors
Service kit for the Solex and Pierburg DIDTA 32-32 series carburetors, as used on, amongst others, the:
This rebuild kit contains, amongst others, the following parts to service 1 carburettor as depicted in the photo:
Please note that this carburetor was marketed as well as under the Solex brand as under the Pierburg brand.
Although these carburetors were originally delivered on the above cars, they are often transplanted onto other cars and engines so the range of vehicles that these service kits might fit is much broader.
Alternatively, your car might no longer be equipped with the carburetor that it left the factory with.
So, please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.
This is a Carburetor City service kit of superior Italian manufacture.
Service Kit for Solex Pierburg 32-32 DIDTA carburetors for BMW 2002
Elaborate Service kit for the Solex 32 PBIC carburetors.
This service kit contains, amongst others, the following parts to service 1 carburettor:
Please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.
This is a Carburetor City service kit of outstanding Italian manufacture.
Carburetor City Article Number: CCR9316
Elaborate Rebuild Kit for Solex 32 PBIC Carburetors - CCR9316
Service kit for the Solex 32 PICB and 34 PICB carburetors.
Carburetor City Article Number: CCR34PICBE
Elaborate Rebuild Kit for Solex 34 PICB Carburetors - CCR34PICBE
Rebuild Kit for Solex 40 RAIP carburetors as used on, amongst others, the Renault RVI Saviem.
It contains, amongst others, the following parts to freshen up 1 carburetor:
Article Number: FR0706
Rebuild Kit for Solex 40 RAIP Carburetors for Renault RVI Saviem - FR0706
Top cover gasket Weber DCZ Carburetors.
Required quantity per carburator: 1
This is number 9 in the drawing.
Weber Part Number: 41705.011
(9) Top Cover Gasket for Weber DCZ Carburetors - 41705.011
Service kit for the Solex and Pierburg PIC and PICT carburetors as used mainly on the following Volkswagen models:
It fits the following variations of the Pierburg and Solex PICT and PIC carburetors:
Please note that both the Solex PIC and Solex PICT were also sold as Pierburg PIC and Pierburg PICT.
Carburetor City Article Number: FR1118
Service Kit for Solex and Pierburg PIC and PICT carburetors for Volkswagen - FR1118
Rebuild kit for the Solex and Pierburg PDSI 30-35 series carburetors as used on, amongst others, the:
Carburetor City Article Number: solex3035pdsi
Rebuild Kit for Solex Pierburg 30-35 PDSI carburetors for Opel Kadett - solex3035pdsi
The automatic choke mechanisms of the Weber DGAS carburetors are known to become cumbersome when they're coming of age.
This can result in a partially activated choke and consequently and overly rich mixture.
This manual conversion kit completely replaces the "automatic" part in the choke mechanism and replaces it with a hand-operated cable system.
This kit contains all the parts depicted with the exception of the carburetor in picture 2 which is solely used for illustration purposes and it not included in the kit or price.
The set includes clear instructions in English.
Weber Part number: 45052
Manual Choke Conversion Kit for Weber DGAS carburetors - 45052
Replacement Pump Diaphragm for Dellorto FZD carburetors.
Replaces part number 6753 which is no longer produced.
This is item number 46 in the drawing.
Dellorto Part Number: 7372
(46) Pump Diaphragm for Dellorto FZD carburetors - 7372
Top, or float chamber, cover gasket for Weber 44 IDF carburetors.
Please note that this gasket fits the 44 mm version of the IDF ONLY.
Other sizes use different gaskets and there is a myriad of different gaskets so please compare your old gasket carefully with the one in the photograph to make sure that it is the right one.
This is item number 6 in the drawing.
Weber Part Number: 41705.086
(6) Top Cover Gasket for Weber 44 IDF carburetors - 41705.086
Rebuild Kit for Solex Pierburg 36/40 en 38 PDSI carburetors as used on, amongst others, the following cars:
Contains, amongst other, the following parts to service 1 carburettor:
Article Number: FR6922
Rebuild Kit for Solex Pierburg 36/40 en 38 PDSI carburetors for BMW and Mercedes
Metal Fuel Line Adapter 12 mm - 10 mm.
This is coupling to connect two pieces of flexible fuel line.
This concerns one fuel line with an internal diameter of 12 mm and one with an internal diameter of 10 mm.
Overall length: 50 mm
Adds a mere 9 mm to the length of your fuel line.
Despite the barbed ends, we do advise you to use our premium quality jubilee clips to secure your fuel line onto this joiner.
Alternatively, you can go HERE for our accessories for 10 mm fuel line or HERE for our accessories for 12 mm fuel line.
Fuel Line Joiner 12 mm - 10 mm
Dellorto factory-original service kit for the early Dellorto SHA 12 series carburetors with rectangular float bowl.
Contains the seals, o-rings and other parts to freshen up 1 carburetor.
This is item number 52 in the drawing.
Dellorto Article Number: 52540
(52) Service Kit for Dellorto SHA 12 carburetors - 52540
Dellorto, Weber and Solex Carburettors Spare Parts Jets Chokes Emulsion Tubes Service Kits