Carter Electrical Fuel Pumps
Carter Electrical Fuel Pumps

Carter Electrical Fuel Pumps

Carter Electrical Fuel Pumps.

On this page you will find our offerings on the electrical fuel pumps by Carter.

Carter Electrical Fuel Pumps

!
CARTERW4259
Carter 6 Volt Low-Pressure Fuel Pump - Dual Polarity

Carter 6 Volt Low-Pressure Fuel Pump - Dual Polarity

This is a special fuel pump for vehicles with a 6 Volt electrical system.

What makes this pump extra special is the fact that it is a Dual-Polarity pump. In other words: it is both suitable for vehicles with a Negative Earth as well as vehicles with a Positive Earth.

Despite being a 6 Volt pump, the output is an incredible 72 Gallons per Hour or 270 Liters!

Thanks to its low output pressure of 5.75 PSI / 0.4 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

In case you still need to reduce the pressure, our Pressure Regulators can be found HERE.

Pump specification:

  • Flow rate: 72 Gallons/hour - 270 liters/hour
  • Pressure: 5.75 PSI / 0.4 Bar
  • Pipe union thread size: 1/4" NPT tapered thread
  • Power supply: 6 Volt Negative Earth AND 6 Volt Positive Earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol or Diesel

The kit includes:

  • Pump
  • Mounting bracket and materials
  • 10 mm inlet and outlet unions with spring-type hose clips

Couplings Specifications:
Connection to pump body: 1/4" NPT tapered thread
Fuel Unions for fuel lines with 10 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.

As an alternative, you can use our Loctite 542 Thread Sealant which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

Carter 6 Volt Low-Pressure Fuel Pump - Dual Polarity

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape